What does LG Oven Clicking but Won't Light - Causes & Fix mean?

Usually a weak bake igniter that glows but can't draw enough current to open the gas valve. Replace the igniter if it glows over 90 seconds without lighting.

How do I fix LG Oven Clicking but Won't Light - Causes & Fix?

Work through the step-by-step fix below. Start with the quick reset and the most common cause, then check the specific part this guide points to. Most fixes need only basic hand tools and the right replacement part.

Can I keep using my LG appliance with this error showing?

Usually not. LG appliances show this error when a part or safety circuit is out of range, so running it can stop the cycle or make the problem worse. Diagnose and clear the error before normal use.

What part is most commonly replaced for LG Oven Clicking but Won't Light - Causes & Fix?

The parts that most often fix LG Oven Clicking but Won't Light - Causes & Fix are listed in the parts section of this guide. Match the part to your exact model and serial number before you buy.

Is LG Oven Clicking but Won't Light - Causes & Fix a DIY repair or do I need a technician?

Many fixes are DIY-friendly with basic tools, such as door switches, drain pumps, water inlet valves, thermostats, heating elements, and filters. Sealed-system, refrigerant, gas, or high-voltage work should go to a licensed technician for safety.

LG Oven Clicking but Won't Light - Causes & Fix

LG Oven Clicking but Won’t Light — What’s Happening

The clicking sound means your spark igniter is working and trying to start the burner, but the gas is either not flowing or not igniting. LG does not assign a single error code to this symptom. You may see it on a stovetop burner or inside the oven cavity during bake or broil.

For the oven bake burner, the most common scenario is a weak igniter that glows orange or white for a long time but never opens the gas safety valve. The igniter needs to draw enough current to prove it is hot before the valve releases gas. If it cannot pull that current, you get a glow and a click but no flame.

Jump to Fix

Most Likely Causes

Weak or failed bake igniter The igniter glows but does not draw the roughly 3 amps needed to open the gas safety valve, so the burner never lights even after 90+ seconds.
Burner cap or head not seated correctly On stovetop burners, a misaligned cap or head prevents the spark from reaching the gas and stops ignition.
Moisture or debris around the burner Water, grease, or food particles on the burner cap, head, spark plug, or heat sensor short out the spark or block the gas flow.
Clogged burner hole or nozzle A blocked orifice stops gas from reaching the ignition point even when the spark is present.
Gas supply valve closed or gas interrupted If the shutoff valve behind the range is closed or your gas service is down, no burners will light.
Loose or damaged spark wire A burned or disconnected wire to the spark electrode stops the spark from forming at the burner.
Defective spark module The module that sends voltage to the spark electrode can fail, preventing any spark on the affected burners.

How to Diagnose and Fix

Determine whether one burner or all burners and the oven are affected, since LG separates single-burner faults from whole-appliance gas supply problems.
Check that the gas shutoff valve behind the range is fully open and that you have gas service to the home.
If all burners fail to light, turn the gas valve off and on several times, wait a moment, and retry to clear any air in the line.
For a stovetop burner, remove the burner cap and head, inspect for moisture or food debris, clean all surfaces, and reinstall the cap level and centered on the head.
Check the burner hole or nozzle for blockage and clear it gently with a pin or compressed air if clogged.
For an oven that won’t light, turn off the circuit breaker for 30 seconds to reset the control, then start a bake cycle and watch the igniter.
Time how long the bake igniter glows before it either lights the burner or times out. LG considers 30 to 60 seconds normal, and anything over 90 seconds without flame indicates a weak igniter that must be replaced.
Inspect the spark wire at the affected burner for looseness, cracks, or heat damage, and replace the wire if compromised.

Parts You Might Need

Part	Notes
LG gas oven bake igniter	Amazon \| Must draw around 3 amps to open the safety valve. Verify your model number before ordering.
Spark electrode wire	Amazon \| High-voltage wire from the spark module to the burner. Replace if cracked or burned.
Spark module (ignition control)	Amazon \| Supplies spark voltage to stovetop burners. Test before replacing if sparking is weak or absent.

If your appliance also shows a code on the display, these match this problem:

When to Call a Pro

Call a pro if you are not comfortable working with gas connections or if basic cleaning and a circuit reset do not solve the problem. Replacing an oven igniter requires pulling the range out, accessing the burner box, disconnecting the old igniter, and confirming that the new part draws correct current before reassembly. If a new igniter still does not light the oven, a technician will need to test the gas valve, safety valve, and control board output to find the fault. Any work that involves disconnecting gas lines or testing live high-voltage spark circuits is best left to a qualified appliance technician. For gas line, burner, or igniter work, or if you ever smell gas, stop and call a licensed technician.