Tag: gas
All the articles with the tag "gas".
-
York Furnace Igniter Not Working - Causes & Fix
Usually a cracked igniter or dirty flame sensor causing ignition lockout. Check LED code, inspect igniter for cracks, and clean sensor.
-
Lennox Furnace Igniter Not Working - Causes & Fix
Usually a cracked hot surface igniter that can't reach ignition temperature. Also check gas supply, flame sensor, and control board output.
-
Kenmore Oven Display Not Working - Causes & Fix
A dead display usually means the main control board isn't sending power to the display board. Check incoming power first, then replace the main control board if needed.
-
Kenmore Oven Self-Clean Not Working - Causes & Fix
Usually a failed door lock assembly that won't latch or report locked status. Check that the door closes fully, then test the lock motor and switch.
-
Kenmore Oven Door Won't Lock - Causes & Fix
A failed door lock motor or control board is usually why a Kenmore oven door won't lock. Replace the lock assembly or main control.
-
Kenmore Oven Igniter Not Working - Causes & Fix
A weak hot-surface igniter that glows but doesn't draw enough current to open the gas valve is the most common cause. Replace the igniter.
-
Kenmore Oven Broiler Not Working - Causes & Fix
Most often a burned-out broil element. Check the element for visible breaks or blistering, then test for continuity and replace if open.
-
Kenmore Oven Temperature Not Accurate - Causes & Fix
A Kenmore oven running too hot or cold is usually caused by a miscalibrated control or a failed temperature sensor. Test with an oven thermometer and recalibrate through the control panel, or replace the sensor if it reads far from 1,080 ohms at room temperature.
-
Kenmore Oven Not Heating - Causes & Fix
A burnt-out bake element (electric) or weak igniter (gas) is the most common cause. Test for continuity or observe glow, then replace.
-
Maytag Oven Display Not Working - Causes & Fix
Most often Control Lock is enabled or a power interruption put the control into a fault state. Reset the breaker for 1 minute.
-
Maytag Oven Heats Too Hot - Causes & Fix
A faulty temperature sensor is the most common cause. Compare actual oven temp with a manual thermometer and replace the sensor if needed.
-
Maytag Oven Won't Stop Beeping - Causes & Fix
Usually a faulty temperature sensor sending bad signals. Reset the breaker for 5 minutes to clear the alarm, then test the sensor.
-
Maytag Oven Self Clean Not Working - Causes & Fix
The self-clean cycle will not start because the control does not see the door locked. Usually a damaged door latch or failed latch switch.
-
Maytag Oven Igniter Not Working - Causes & Fix
Usually a failed hot-surface igniter that glows weakly or draws too little current to open the gas valve. Replace the igniter.
-
Maytag Oven Broiler Not Working - Causes & Fix
A Maytag oven broiler that won't work is usually a failed broil element (electric) or weak igniter (gas). Replace the defective part.
-
KitchenAid Oven Display Not Working - Causes & Fix
Usually a hidden-display setting or power reset issue. Press and hold Clock Set/Start for five seconds to restore the display.
-
Frigidaire Oven Display Not Working - Causes & Fix
Usually a tripped breaker or control glitch. Reset power for 30 seconds. If the display stays blank, the control board has likely failed.
-
GE Oven Display Not Working - Causes & Fix
A failed display board or main control board not supplying power to the display is the most common cause. Replace the display board or control board after verifying power and ribbon connections.
-
Whirlpool Oven Display Not Working - Causes & Fix
A blank Whirlpool oven display usually means a tripped circuit breaker or failed control board. Reset the breaker for 1 minute first.
-
LG Oven Display Not Working - Causes & Fix
Loose wiring harness between control and display boards causes most blank screens. Reseat connectors or replace control board.
-
LG Oven Igniter Not Working - Causes & Fix
Most LG gas ovens fail to ignite when the bake igniter is too weak to draw enough current to open the valve. Replace the igniter.
-
Samsung Oven Display Not Working - Causes & Fix
Usually caused by a failed main control board or user interface board. Check power supply, reset the unit, then test DC voltages at connectors to isolate the fault.
-
Samsung Oven Self-Clean Not Working - Causes & Fix
Usually a failed door lock assembly or latch microswitch that prevents the cycle from starting or causes it to abort mid-cycle.
-
KitchenAid Gas Oven Safety Valve Replacement - Signs & How-To
Oven won't heat but cooktop works, or oven igniter glows without gas? A failed gas oven safety valve or regulator shut-off stops gas flow. Replacing it restores oven function.