What does Frigidaire Oven Clicking but Won't Light - Causes & Fix mean?

Most often a weak igniter that glows but can't draw enough current to open the gas valve. Replace the igniter to restore lighting.

How do I fix Frigidaire Oven Clicking but Won't Light - Causes & Fix?

Work through the step-by-step fix below. Start with the quick reset and the most common cause, then check the specific part this guide points to. Most fixes need only basic hand tools and the right replacement part.

Can I keep using my Frigidaire appliance with this error showing?

Usually not. Frigidaire appliances show this error when a part or safety circuit is out of range, so running it can stop the cycle or make the problem worse. Diagnose and clear the error before normal use.

What part is most commonly replaced for Frigidaire Oven Clicking but Won't Light - Causes & Fix?

The parts that most often fix Frigidaire Oven Clicking but Won't Light - Causes & Fix are listed in the parts section of this guide. Match the part to your exact model and serial number before you buy.

Is Frigidaire Oven Clicking but Won't Light - Causes & Fix a DIY repair or do I need a technician?

Many fixes are DIY-friendly with basic tools, such as door switches, drain pumps, water inlet valves, thermostats, heating elements, and filters. Sealed-system, refrigerant, gas, or high-voltage work should go to a licensed technician for safety.

Frigidaire Oven Clicking but Won't Light - Causes & Fix

Frigidaire Oven Clicking but Won’t Light — What’s Happening

On a Frigidaire gas oven, clicking is the normal sound of the spark ignition system trying to light the burner. When the oven clicks but won’t light, the ignition sequence is starting but failing to complete. This typically means either gas is not reaching the burner or the igniter is not hot enough to open the gas safety valve.

Frigidaire gas ranges use either a hot-surface igniter or a spark igniter to light the oven burner. The clicking you hear confirms the electrical ignition system is trying to fire, but something is preventing flame from establishing. The fault is not a displayed error code, it is a physical ignition or gas-flow problem.

Jump to Fix

Most Likely Causes

Weak or faulty oven igniter The igniter may glow but not draw enough current to open the gas valve, so the oven never lights.
Gas supply issue A closed manual shutoff valve, empty supply line, or restricted gas flow will prevent the burner from lighting even when spark is present.
Clogged burner ports or orifice Debris blocking the burner holes or gas orifice stops gas from reaching the igniter area.
Bad temperature sensor or probe A failed oven sensor can prevent the control from starting the heat cycle on many models.
Misaligned or damaged burner parts If the burner head, cap, or igniter is out of position, the spark may not reach the gas stream.
Control board or relay fault If the board does not send power to the igniter circuit, the oven will not heat or light.
Wiring or connection problem Loose, corroded, or broken wiring in the igniter or sensor circuit will interrupt the ignition sequence.

How to Diagnose and Fix

Confirm the range has power at the breaker and outlet, because loss of electrical supply can prevent ignition controls from operating.
Verify the gas supply is on at the manual shutoff valve and that other gas appliances in the home operate normally.
Start a bake cycle and watch the igniter area through the oven window or with the door cracked open to see if the igniter glows and whether gas flows.
Turn off power and gas, remove the oven bottom panel, disconnect the igniter, and test it with a multimeter for continuity and resistance per the model’s service manual.
Test the oven temperature sensor with a multimeter at room temperature (it should read around 1000 to 1100 ohms when cold).
With gas off for safety, check whether 120 V AC is present at the igniter leads when a bake cycle is called for, to confirm the control board is commanding ignition.
Inspect burner ports and the gas orifice for grease, carbon, or debris, and clean with a soft brush or compressed air if clogged.
Replace the failed igniter, temperature sensor, or control board as indicated by your test results, then restore power and gas and run a full bake cycle to confirm the oven lights and heats normally.

Parts You Might Need

Part	Notes
Oven igniter (hot-surface or spark type)	Amazon \| Match the igniter style and part number to your Frigidaire model
Oven temperature sensor (probe)	Amazon \| Should read 1000–1100 ohms cold
Oven control board or relay	Amazon \| Only if testing confirms no voltage output to igniter circuit

If your appliance also shows a code on the display, these match this problem:

When to Call a Pro

Gas appliance ignition work requires safe isolation of both electrical and gas supply, correct diagnosis with a multimeter, and proper reassembly to prevent gas leaks or fire hazards. If you are not comfortable working around natural gas or propane, shut off the gas at the manual valve and call a qualified appliance technician or gas service professional. Any time you smell gas, do not attempt repairs. Leave the home, call your gas utility or fire department from outside, and do not operate electrical switches or ignition sources. For gas line, burner, or igniter work, or if you ever smell gas, stop and call a licensed technician.