Skip to content
Industrial Error Code Fixes
Go back

More industrial fault codes

VFD Trip Reset Guide: How to Clear Fault Codes Safely

⚡ Quick Answer

Complete guide to resetting VFD trip codes safely, including ABB, Yaskawa, Allen-Bradley, Danfoss, Siemens, and other major drive brands.

⚡ AT A GLANCEScroll down for full repair guide
What it meansVFD trip reset procedures for overcurrent, ground fault, overvoltage, undervoltage, overtemp, and communication faults across major brands
Most likely causeLoad jam, short ramp time, motor/cable insulation failure, fast decel, line voltage sag, blocked cooling, or PLC communication loss
First checkRead fault code and history, check mechanical issues and power supply, isolate motor for ground faults, reset via proper path, monitor after restart
⏱Repair time15 minutes to 2 hours depending on fault cause
🔧Part neededClamp meter, megohmmeter, braking resistor, line reactor, cooling fan

Parts to price first

Check the part before you book service.

Fluke 323 True-RMS Clamp Meter

Clamp meter for measuring VFD output current under load to diagnose overcurrent trips.

$80-$140Check price

Megger Insulation Tester 1000V

Megohmmeter for testing motor and cable insulation resistance to diagnose ground fault trips.

$150-$400Check price

VFD Braking Resistor

Braking resistor for VFD overvoltage trips during deceleration of high-inertia loads.

$50-$200Check price

VFD Input Line Reactor

Line reactor to smooth incoming power and prevent undervoltage trips caused by supply harmonics.

$80-$300Check price

Equipment service manual download (eManualOnline)

The full OEM-style workshop manual has the wiring diagram, test values, and the fault table this guide summarizes. Instant PDF download.

Repair intent

Need this fixed instead of diagnosed?

Complete guide to resetting VFD trip codes safely, including ABB, Yaskawa, Allen-Bradley, Danfoss, Siemens, and other major drive brands.

VFD Trip Reset Guide: How to Clear Fault Codes Safely

Resetting a VFD trip is easy. Resetting it safely is the real job. Overcurrent, ground fault, overvoltage, undervoltage, overtemperature, and communication faults all clear in slightly different ways, but the rule is the same: identify whether the trip was caused by the load, the motor, the power source, the setup, or the drive itself before you hammer the reset button.

Jump to Fix

Common VFD Trip Types

Symptom / CodeCommon MeaningTypical Brands
OvercurrentLoad jam, short ramp, or output shortABB, Yaskawa, Allen-Bradley, Danfoss
Ground faultMotor or cable insulation leakAll major VFDs
OvervoltageFast decel or regenerative loadAll major VFDs
UndervoltageLow line voltage or phase lossAll major VFDs
OvertempCooling failure or overloaded driveAll major VFDs
CommunicationPLC / keypad / fieldbus lossNetworked systems

When a simple reset is fine

A nuisance communication glitch or a known utility sag may clear cleanly once. Even then, it is worth checking logs before resuming full production.

When not to reset blindly

Ground fault, repeated hardware overcurrent, and short-circuit style trips should not be reset repeatedly. Those are the faults that destroy replacement drives if the motor or cable is bad.

Best practice sequence

Read the code, review history, isolate motor if needed, verify line power, then reset and monitor. That sequence beats guesswork every time.

Step-by-Step Fix

  1. Capture the fault code and time — Write it down or pull the log before power cycling.
  2. Look for obvious mechanical issues — Jam, seized bearing, blocked conveyor, or overloaded pump first.
  3. Check power and cooling — Undervoltage and overtemp faults often have simple physical causes.
  4. Isolate motor and cable for serious trips — Ground and hardware overcurrent faults demand insulation testing.
  5. Reset through the proper path — Use keypad reset, digital input reset, or PLC reset per the drive design. Avoid random power cycling as your only method.
  6. Monitor after restart — Watch current, temperature, and trip timing during a real load cycle.

Parts and Tools Often Needed

ItemNotes
MegohmmeterEssential for grounding and insulation faults
Clamp meterCheck current draw under load
Cooling fanDrive overtemp issues
Brake resistorNeeded for repeat overvoltage decel trips
Input fusesFor undervoltage and phase-loss issues
Parameter backupAlways save settings before replacing a drive

Need Replacement Parts?

Before ordering, match the drive part to the model number, electrical rating, and failure symptom. Check current prices on Amazon - prices and availability change frequently.

When to Call a Pro

If a VFD keeps tripping on the same code after one informed reset attempt, the reset was never the fix. At that point you need diagnosis, not more resets.


Need a professional? Compare Industrial repair options before replacing parts.
Compare Repair Options
Share this post on:

Previous Post
Siemens VFD Fault Codes List: F0001, F00002, G120, V20 and Micromaster
Next Post
VFD Fault Codes: Complete Troubleshooting Guide