Posts
All the articles I've posted.
-
Allen-Bradley PowerFlex vs Siemens SINAMICS — An Industrial Tech's Honest Comparison (2026)
For a plant that's already standardized on Rockwell ControlLogix or CompactLogix PLCs and uses EtherNet/IP as its primary fieldbus, buy Allen-Bradley...
-
Samsung vs LG French-Door Refrigerators — An Appliance Tech's Honest Comparison (2026)
If you want a feature-rich French-door refrigerator with the most-developed smart-home integration and a generally lower service-call rate over 5-8 years,...
-
Schneider Altivar OCF Fault — Overcurrent Fix
Schneider Altivar OCF (Overcurrent Fault) on the ATV320, ATV340, ATV630, ATV930, and most legacy ATV61/71 drives means the drive's IGBT power module...
-
Schneider Altivar OSF Fault — Overspeed Fix
Schneider Altivar OSF (Overspeed Fault) means the drive's speed feedback (calculated from the back-EMF model in open-loop or from a real encoder in...
-
Scotsman 6-Flash Code — Refrigerant Pressure Out of Range Fix
A 6-flash code on a Scotsman Brilliance-series ice machine means the controller has detected refrigerant pressure outside the expected operating range —...
-
Siemens SINAMICS G120 F30011 Fault — Phase Loss Fix
SINAMICS G120 F30011 (Line Phase Loss) means the Power Module's input phase-monitoring logic detected that one of the three input phases is missing or...
-
Siemens SINAMICS G120 F30021 Fault — Ground Fault Fix
SINAMICS G120 F30021 (Ground Fault) means the Power Module's output current sensors saw an imbalance — current flowing out the U, V, W phases summed to a...
-
Sub-Zero Refrigerator Error Code EC — Evap Fan Fix
Sub-Zero refrigerators display "EC" (sometimes shown as "EC 38" or "EC 39" with sub-code) when the main control board detects an evaporator fan circuit...
-
Takagi Code 111 — No Ignition Fix
Code 111 on a Takagi tankless water heater (T-H3, T-H3J, T-K4, T-D2, T-KJr2, T-M50, and the newer Tx2 condensing platforms) means the unit attempted...
-
Tempstar 4-Flash Error Code — Limit Switch Fix
A Tempstar 4-flash code means the integrated furnace control opened the gas valve on a heat call, but a high-limit safety switch (either the primary heat...
-
Trane 3-Blink Error Code — Pressure Switch Fault Fix
A 3-blink fault on a Trane furnace LED means the integrated furnace control did not see the pressure switch close after the inducer started, or...
-
Trane XV20i/XV18 Fault 126 — Low Pressure Cutout Fix
Fault 126 on a Trane XV20i, XV18, or XL20i variable-speed heat pump means the outdoor unit's low-pressure switch opened — refrigerant suction pressure...
-
Trane Voyager RTU Error Code 31 — Fix
Trane Voyager rooftop unit (RTU) error code 31 on the UCM (Unit Control Module) or Tracer SC controller indicates a high-pressure cutout — the...
-
Viking Range Error Code F0 — Control Board Fault Fix
Viking range error F0 (sometimes shown as "F-0" or just blinking "F" on older models) indicates the electronic oven control (EOC) has detected an internal...
-
Vulcan/Wolf Convection Oven F-Code Error — Gas Oven Fix
Vulcan and Wolf (commercial Wolf, not residential Sub-Zero Wolf) gas convection ovens display F-series error codes (F1 through F9 depending on model) when...
-
Weil-McLain Code 1 — No Flame Sensed Fix
Code 1 on a Weil-McLain Gold or Ultra Series boiler means the boiler attempted ignition but did not prove flame within the trial-for-ignition window...
-
Weil-McLain Code 3 — Low Water Cutoff Fix
Code 3 on a Weil-McLain Gold or Ultra Series boiler (Ultra 80/105/155/230/310/399, GV90+, and WM97+ platforms) indicates a low water cutoff (LWCO) lockout —...
-
Yaskawa GA800 oC Fault — Overcurrent Fix
Yaskawa GA800 oC (Overcurrent) means the output current sensors on at least one of the U, V, or W phases saw current exceed roughly 200% of the drive's...
-
Yaskawa GA800 oV Fault — DC Overvoltage Fix
Yaskawa GA800 oV (DC Overvoltage) means the internal DC bus climbed above approximately 820 VDC on a 480V-class drive (or 410 VDC on a 240V-class) while the...
-
Yaskawa GA800 Uv1 Fault — DC Undervoltage Fix
Yaskawa GA800 Uv1 (DC Bus Undervoltage) means the DC bus dropped below the L2-05 threshold (default 380 VDC for a 480V-class drive, 190 VDC for a...
-
York 2-Blink Error Code — Pressure Switch Stuck Open Fix
A York 2-blink fault means the integrated furnace control did not see the pressure switch close after the inducer (draft motor) started running — meaning...
-
Allen-Bradley PowerFlex F004 Fault — Undervoltage Fix
PowerFlex F004 (Undervoltage) means the DC bus dropped below the drive's minimum threshold while running — about 310 VDC on a 480V-class PowerFlex 525,...
-
Allen-Bradley PowerFlex F005 Fault — Overvoltage Fix
PowerFlex F005 (DC Bus Overvoltage) means the bus exceeded the drive's ceiling — about 810 VDC on a 480V-class PowerFlex 525, around 405 VDC on a...
-
Allen-Bradley PowerFlex F012 Fault — HW Overcurrent Fix
PowerFlex F012 (Hardware Overcurrent) is a hard-tripped, microsecond-scale current fault detected by the gate driver circuitry, not by software. It means...