Posts
All the articles I've posted.
-
Bosch Dishwasher E06 Error - Causes & Fix
E06 on a Bosch dishwasher means a door sensor or latch circuit fault. Most often the door is not closing fully or the sensor is faulty.
-
Bosch Dishwasher E05 Error Code - Causes & Fix
E05 means a wash arm diverter circuit fault in the main control board. Most common fix: power reset at the breaker for 30 seconds.
-
LG Dryer Burning Smell - Causes & Fix
Lint buildup in the filter housing or vent system is the most common cause. Clean the lint filter, housing, and vent hose fully.
-
Speed Queen Washer Stuck on One Cycle - Causes & Fix
Usually caused by a water fill problem, drain blockage, or lid lock fault preventing the control from advancing to the next step.
-
Speed Queen Washer Shaking and Loud - Causes & Fix
An unbalanced load is the most common cause. Redistribute heavy items evenly, check that the washer is level, and remove shipping bolts if new.
-
Speed Queen Washer Door Won't Unlock - Causes & Fix
Most often the door lock assembly has failed or the washer still senses water in the tub. Reset power, verify drainage, and inspect the lock.
-
Speed Queen Washer Won't Start - Causes & Fix
Usually caused by a lid not registering closed or no incoming power. Check that the lid is fully shut, the power cord is plugged in, and hold Start for two seconds.
-
Amana Washer Won't Turn On - Causes & Fix
Usually a tripped breaker, unplugged cord, or Control Lock enabled. Check power, unlock the console, and verify the lid is closed.
-
Amana Washer Leaking Water - Causes & Fix
Usually a worn door seal, loose inlet hose, or failed pump seal. Check hoses first, inspect the door gasket, then test the pump underneath.
-
Amana Washer Won't Drain - Causes & Fix
Usually a kinked or blocked drain hose. Check for kinks, clear any debris from the pump area, and reset the machine to restore draining.
-
Frigidaire F26 Error Code - Causes & Fix
F26 on Frigidaire ranges means communication error between control board and keypad. Most often fixed by reseating ribbon cable.
-
Maytag LdL Error Code - Causes & Fix
LdL means the lid lock will not lock or has failed. Most often an item under the lid or detergent buildup blocks the lock mechanism.
-
Maytag Washer d9 Error Code - Causes & Fix
d9 means low line voltage detected. Check your outlet voltage first, then inspect the power cord and plug for loose connections.
-
Maytag Oven F1 Error Code - Causes & Fix
F1 means the control lost the oven temperature sensor signal. Most often a failed sensor. Reset power, test sensor, or replace it.
-
Frigidaire Washer Won't Agitate - Causes & Fix
Worn agitator dogs or a failed drive coupler usually stop agitation. Replace the agitator repair kit or coupler to restore wash action.
-
GE Washer Overflowing - Causes & Fix
A GE washer overflowing usually means a failed water inlet valve that won't close or a clogged pressure hose preventing level detection.
-
GE Washer Won't Agitate - Causes & Fix
A worn or slipping drive belt is the most common cause. Enter diagnostic mode to retrieve fault codes, then inspect the belt and pulleys for wear or blockage.
-
Maytag Washer Smells Like Mildew - Causes & Fix
Wet laundry left inside and a closed door prevent drying, leading to mildew buildup. Remove loads promptly, leave the door open, and run a Clean Washer cycle with hot water.
-
Whirlpool Washer Won't Agitate - Causes & Fix
Most often caused by a worn cam/splutch or shift actuator that no longer engages agitate mode. Check drive parts in service mode.
-
LG Washer Won't Agitate - Causes & Fix
A stripped wash plate hub or failed hall sensor on direct-drive models is usually the culprit. Check for free-spinning plates and test motor sensors.
-
Yaskawa GA800 A.116 Fault - Causes & Fix
A.116 means multi-function input open alarm on GA800 VFDs. Most often an open interlock, E-stop, or loose wiring. Check control circuit.
-
Yaskawa GA800 A.112 Alarm - Causes & Fix
A.112 on a Yaskawa GA800 is an alarm for missing or invalid run/reference input. Most often the command source is set wrong on the keypad.
-
Maytag Dryer F6E2 Error Code - Causes & Fix
F6E2 on a Maytag dryer means a communication fault between the main control and user interface. Power-cycle for 5 minutes first.
-
Maytag Dryer F3E2 Error Code - Causes & Fix
F3E2 means the moisture sensor has not registered data for five consecutive loads. Most often the dryer is not level or loads are too small.