Posts

All the articles I've posted.

• LG Dryer tE Error Code - Causes & Fix

  7 Jun, 2026

  tE or tE1 means the thermistor temperature sensor has failed or lost signal. Most often the thermistor itself needs replacement.

• LG Dryer nP Error Code - Causes & Fix

  7 Jun, 2026

  nP means no current detected at the heater, usually from a tripped breaker or lost 240 V leg. Reset the double-pole breaker fully off 10 sec.

• LG Dishwasher E1 Error Code - Causes & Fix

  7 Jun, 2026

  E1 means a leak or overfill triggered the float switch. Most often water pooled in the base pan from a door seal or internal leak.

• Samsung Washer bE3 Error Code - Causes & Fix

  7 Jun, 2026

  bE3 means a button on the control panel is stuck or shorted. Most often caused by a stuck key or debris around the buttons.

• Samsung Washer bE1 Error Code - Causes & Fix

  7 Jun, 2026

  bE1 means a control-panel button is stuck or continuously pressed. Clean the buttons and power-cycle the washer to clear it.

• Samsung Washer bC1 Error Code - Causes & Fix

  7 Jun, 2026

  bC1 means a button is stuck or held down, usually the Power button. Clean the keypad and power-cycle. Most often fixes a stuck button.

• GE Oven F2 Error Code - Causes & Fix

  7 Jun, 2026

  F2 means your GE oven detected over-temperature or runaway heat. The most common fix is replacing the oven temperature sensor.

• Frigidaire Range F10 Error Code - Causes & Fix

  7 Jun, 2026

  F10 means runaway oven temperature detected. The most common fix is replacing the failed oven temperature sensor (RTD).

• GE Range F3 Error Code - Causes & Fix

  7 Jun, 2026

  F3 means the control sees the oven temperature sensor circuit as open or out of range. Usually fix by replacing the sensor.

• Samsung Refrigerator 25E Error - Causes & Fix

  7 Jun, 2026

  25E means defrost failed after 80 minutes. Most often a bad defrost heater or iced-over evaporator coil stops the cycle completing.

• Samsung Washer 4E Error Code - Causes & Fix

  7 Jun, 2026

  4E means water supply problem. Most often caused by a kinked inlet hose or closed valve. Check hose, filter, and tap first.

• Samsung Oven E-27 Error Code - Causes & Fix

  7 Jun, 2026

  E-27 means the oven temperature sensor circuit is open or faulty. The most common fix is replacing the oven temperature sensor.

• Samsung Dryer HC Error Code - Causes & Fix

  7 Jun, 2026

  HC means your Samsung dryer is overheating. Most often it's a clogged lint screen or blocked vent. Clean both and check the exhaust path.

• Yaskawa GA800 E50 Fault Code - Causes & Fix

  6 Jun, 2026

  E50 on a Yaskawa GA800 VFD signals an external fault input from an interlock or safety device. The most common fix is locating and clearing the tripped field switch or relay.

• Yaskawa GA800 E40 Fault - Causes & Fix

  6 Jun, 2026

  E40 is not documented in standard GA800 manuals. Confirm the exact code on the display and check wiring, option cards, and control board.

• Samsung Washer AE Error Code - Causes & Fix

  5 Jun, 2026

  AE means communication error or water leak detected. Check for leaks around door, hoses, and cabinet, then inspect wiring to inverter board.

• Samsung Microwave E-01 Error - Causes & Fix

  5 Jun, 2026

  E-01 means Open Error on Samsung microwaves. Most often a door interlock switch or thermal safety is open. Power reset first, then check door.

• Samsung C-A1 Microwave Error - Causes & Fix

  5 Jun, 2026

  C-A1 means damper-sensing failure: the microwave cannot detect the damper opening or closing for 1 minute. Usually a stuck damper or bad motor.

• Samsung Dryer tO Error Code - Causes & Fix

  5 Jun, 2026

  Samsung tO code means a temperature sensor fault. Most common cause: clogged lint filter or vent trapping heat. Clean both first.

• Samsung Dryer tE Error Code - Causes & Fix

  5 Jun, 2026

  tE means a temperature-sensing fault. The dryer cannot read temperature correctly. Most likely cause: failed thermistor sensor.

• Yaskawa GA800 E06 Fault Code - Causes & Fix

  4 Jun, 2026

  E06 fault on Yaskawa GA800 VFD is not defined in standard documentation. Check your drive's display and manual for the exact code meaning.

• Yaskawa GA800 E05 Fault - Causes & Fix

  4 Jun, 2026

  E05 on a Yaskawa GA800 VFD signals a communication or watchdog error on the industrial network interface. Most often fixed by reseating network cables or correcting node addressing.

• Danfoss FC302 Alarm 32 - Causes & Fix

  4 Jun, 2026

  Alarm 32 on the Danfoss FC302 VFD means motor phase W is missing. Check wiring and connections on the W output phase first.

• Danfoss FC302 VFD Alarm 29 - Causes & Fix

  4 Jun, 2026

  Alarm 29 means heatsink over-temperature. Most common fix: clean blocked air vents, replace failed cooling fans, or clear dust from fins.