Tag: symptom
All the articles with the tag "symptom".
-
Amana Dryer Won't Start - Causes & Fix
Most often a tripped breaker, control lock engaged, or bad door switch. Check power and settings first, then test the door latch and thermal fuse.
-
Frigidaire Dryer Squeaking - Causes & Fix
Usually a worn rear drum bearing or support. Replace the bearing kit, idler pulley, belt, and drum rollers to stop the squeak.
-
LG Dryer Gets Too Hot - Causes & Fix
Blocked exhaust duct or clogged lint screen restricts airflow, causing overheating. Clean the vent system and inspect the thermistor.
-
LG Dryer Burning Smell - Causes & Fix
Lint buildup in the filter housing or vent system is the most common cause. Clean the lint filter, housing, and vent hose fully.
-
Speed Queen Washer Stuck on One Cycle - Causes & Fix
Usually caused by a water fill problem, drain blockage, or lid lock fault preventing the control from advancing to the next step.
-
Speed Queen Washer Shaking and Loud - Causes & Fix
An unbalanced load is the most common cause. Redistribute heavy items evenly, check that the washer is level, and remove shipping bolts if new.
-
Speed Queen Washer Door Won't Unlock - Causes & Fix
Most often the door lock assembly has failed or the washer still senses water in the tub. Reset power, verify drainage, and inspect the lock.
-
Speed Queen Washer Won't Start - Causes & Fix
Usually caused by a lid not registering closed or no incoming power. Check that the lid is fully shut, the power cord is plugged in, and hold Start for two seconds.
-
Amana Washer Won't Turn On - Causes & Fix
Usually a tripped breaker, unplugged cord, or Control Lock enabled. Check power, unlock the console, and verify the lid is closed.
-
Amana Washer Leaking Water - Causes & Fix
Usually a worn door seal, loose inlet hose, or failed pump seal. Check hoses first, inspect the door gasket, then test the pump underneath.
-
Amana Washer Won't Drain - Causes & Fix
Usually a kinked or blocked drain hose. Check for kinks, clear any debris from the pump area, and reset the machine to restore draining.
-
Frigidaire Washer Won't Agitate - Causes & Fix
Worn agitator dogs or a failed drive coupler usually stop agitation. Replace the agitator repair kit or coupler to restore wash action.
-
GE Washer Overflowing - Causes & Fix
A GE washer overflowing usually means a failed water inlet valve that won't close or a clogged pressure hose preventing level detection.
-
GE Washer Won't Agitate - Causes & Fix
A worn or slipping drive belt is the most common cause. Enter diagnostic mode to retrieve fault codes, then inspect the belt and pulleys for wear or blockage.
-
Maytag Washer Smells Like Mildew - Causes & Fix
Wet laundry left inside and a closed door prevent drying, leading to mildew buildup. Remove loads promptly, leave the door open, and run a Clean Washer cycle with hot water.
-
Whirlpool Washer Won't Agitate - Causes & Fix
Most often caused by a worn cam/splutch or shift actuator that no longer engages agitate mode. Check drive parts in service mode.
-
LG Washer Won't Agitate - Causes & Fix
A stripped wash plate hub or failed hall sensor on direct-drive models is usually the culprit. Check for free-spinning plates and test motor sensors.
-
Fujitsu Mini Split Not Cooling - Causes & Fix
Dirty air filters blocking airflow are the most common cause. Clean or replace filters, then check for error codes on the indoor LED.
-
Daikin Mini Split Not Cooling - Causes & Fix
Usually caused by dirty indoor air filters or incorrect thermostat settings. Clean or replace the filter and verify cooling mode and setpoint.
-
Mitsubishi Mini Split Not Cooling - Causes & Fix
Most often dirty air filters or blocked coils trigger protective shutdown. Clean filters, check fault code via failure mode recall, and inspect wiring.
-
Rheem Furnace Igniter Not Working - Causes & Fix
Most often the igniter element has cracked or failed open. Test it with a multimeter at the leads for continuity and replace if open.
-
Rheem Furnace Not Heating - Causes & Fix
A dirty flame sensor is the most common cause. Clean the sensor rod with fine steel wool or emery cloth and verify the gas valve is open.
-
Trane Furnace Igniter Not Working - Causes & Fix
Usually a cracked or failed hot-surface igniter. Less often, bad wiring, a faulty control board, or a gas valve issue prevents ignition.
-
Goodman Furnace Igniter Not Working - Causes & Fix
The igniter is likely failed and not glowing when voltage is applied. Verify the igniter receives 115–120 VAC during ignition.