Tag: appliance

All the articles with the tag "appliance".

• Whirlpool F0E1 Error Code - Causes & Fix

  8 Jun, 2026

  F0E1 on Whirlpool washers means the Clean Washer cycle started with items still inside. Remove all contents and restart the cycle empty.

• Whirlpool drn Error Code - Causes & Fix

  8 Jun, 2026

  Whirlpool drn (F9 E1) means the washer is draining too slowly. Check the drain hose installation and pump for blockages first.

• Whirlpool Washer F02 Error Code - Causes & Fix

  8 Jun, 2026

  F02 means the washer tub isn't draining in time. Check for a kinked or clogged drain hose, then clean the pump filter if the hose is clear.

• Whirlpool Refrigerator PO Error Code - Causes & Fix

  8 Jun, 2026

  PO means Power Outage: the freezer warmed to 18°F or higher. Press MEASURED FILL to clear the alert, then check your breaker and outlet.

• Whirlpool Refrigerator E9 Error Code - Causes & Fix

  8 Jun, 2026

  E9 means the freezer temperature is too high. Most often caused by a door left ajar or warm food loaded in. Reset power for 1 minute first.

• Whirlpool Refrigerator E5 Error - Causes & Fix

  8 Jun, 2026

  E5 on Whirlpool refrigerators signals an ice-maker temperature sensor mismatch. Most often the ice-room thermistor has failed.

• Whirlpool Refrigerator E4 Error Code - Causes & Fix

  8 Jun, 2026

  E4 signals a defrost sensor fault in the fresh-food compartment. Most often a failed sensor or wiring; reset power first.

• Whirlpool Refrigerator E1 Error Code - Causes & Fix

  8 Jun, 2026

  E1 on a Whirlpool refrigerator is model-specific. Most often a control glitch fixed by unplugging for one minute then restoring power.

• Whirlpool Refrigerator E2 Error Code - Causes & Fix

  8 Jun, 2026

  E2 on Whirlpool refrigerators is model-specific: often an ice maker cycle failure. Most common fix: replace the ice maker module.

• Whirlpool Refrigerator E0 Error Code - Causes & Fix

  8 Jun, 2026

  E0 on Whirlpool fridges often means no ice maker fault detected (diagnostic mode) or power loss/open door, depending on your model.

• Whirlpool Refrigerator dF Error Code - Causes & Fix

  8 Jun, 2026

  dF means defrost failure on Whirlpool refrigerators. The most common fix is replacing the defrost heater or defrost thermostat.

• Whirlpool Range PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure detected by the control. Press Cancel to clear it. If it returns, check your breaker and terminal-block wiring.

• Whirlpool Range SAB Error Code - Causes & Fix

  8 Jun, 2026

  SAB means Sabbath Mode is on, not a fault. Turn off Sabbath Mode using your model's key sequence (check the owner's manual).

• Whirlpool Range LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means the control lock feature is enabled, not a fault. Press and hold START/ENTER for 5 seconds to unlock the keypad and restore use.

• Whirlpool Range LOC Error Code - Causes & Fix

  8 Jun, 2026

  LOC means Control Lock is enabled, not a failure. Press and hold START/ENTER for 5 seconds to unlock. If it persists, reset the breaker.

• Whirlpool Range FC E5 Error - Causes & Fix

  8 Jun, 2026

  FC E5 on a Whirlpool range signals a Wi-Fi antenna or wiring fault. Most often a loose connector or failed antenna module.

• Whirlpool FC E4 Error Code - Causes & Fix

  8 Jun, 2026

  FC E4 on a Whirlpool wall oven signals a Wi-Fi antenna or wiring fault. Most likely fix: power-cycle the oven at the breaker.

• Whirlpool FC E3 Error - Causes & Fix

  8 Jun, 2026

  FC E3 means the range lost its Wi-Fi connection to your router. Most often fixed by power-cycling the range and resetting the router.

• Whirlpool Range FC E2 Error - Causes & Fix

  8 Jun, 2026

  FC E2 is not a verified Whirlpool range code. You likely saw F3 E2 (oven sensor fault) or F2 E2 (keypad connection fault).

• Whirlpool Range F9 Error Code - Causes & Fix

  8 Jun, 2026

  F9 / F9 E0 means the range detected a power-supply or wiring problem. Most often fixed by checking the outlet and terminal connections.

• Whirlpool Range F8 Error Code - Causes & Fix

  8 Jun, 2026

  F8 on a Whirlpool range means meat probe or cooling fan fault. Most often the meat probe is not fully seated in the jack.

• Whirlpool Range F7 Error Code - Causes & Fix

  8 Jun, 2026

  F7 on Whirlpool ranges usually means door-latch or control-board fault. Reset power at the breaker for 1 minute and check wiring first.

• Whirlpool Range F5 Error Code - Causes & Fix

  8 Jun, 2026

  F5 signals a door latch assembly, latch switch, or wiring fault. Most often a failed door latch assembly. Reset power first.

• Whirlpool Range F4 Error Code - Causes & Fix

  8 Jun, 2026

  F4 means a temperature sensor fault. The most likely fix is replacing the oven temperature sensor (RTD), which costs $20–60 and takes 30 min.