Tag: appliance

All the articles with the tag "appliance".

• Bosch E02 Error Code - Causes & Fix

  8 Jun, 2026

  E02 on Bosch dishwashers means a main control board relay fault in the heating circuit. Most often the control board itself has failed.

• Amana Refrigerator PO Error Code - Causes & Fix

  8 Jun, 2026

  PO means Power Outage: the freezer warmed to 18°F or higher during a power loss. Press MEASURED FILL under Confirm to clear the alert.

• Amana Refrigerator F1 Error Code - Causes & Fix

  8 Jun, 2026

  F1 on Amana refrigerators is not documented by the manufacturer. Check your model's wiring diagram or manual for the exact meaning.

• Whirlpool Washer Sud Error Code - Causes & Fix

  8 Jun, 2026

  Sud/Sd means excess suds detected. Let the cycle finish-Whirlpool runs a suds-reduction routine. Most often caused by too much HE detergent.

• Whirlpool Washer PF Error Code - Causes & Fix

  8 Jun, 2026

  PF means power failure during the wash cycle. Press POWER to clear or hold START to resume. Check outlet voltage and connections first.

• Whirlpool Washer Lid Error Code - Causes & Fix

  8 Jun, 2026

  Lid error means the washer detects the lid is open. Close the lid fully to clear the code. If it persists, check for obstructions.

• Whirlpool LdU Error Code - Causes & Fix

  8 Jun, 2026

  LdU means the lid cannot unlock. Remove items from the lid and check for jammed objects. If clear, the lid-lock assembly likely failed.

• Whirlpool Refrigerator E6 Error Code - Causes & Fix

  8 Jun, 2026

  E6 / F6 means a communication error between the main control and display. Power-reset the fridge first-often fixes it immediately.

• Whirlpool LdL Error Code - Causes & Fix

  8 Jun, 2026

  LdL means the lid isn't locking. Most often caused by clothing blocking the strike or detergent buildup around the lock mechanism.

• Whirlpool HC Error Code - Causes & Fix

  8 Jun, 2026

  HC means hot and cold inlet hoses are reversed. Fix: turn off water, swap the hoses so hot connects to hot and cold to cold.

• Whirlpool F8E2 Error Code - Causes & Fix

  8 Jun, 2026

  F8E2 means a dispenser fault on Whirlpool dishwashers and washers. Most common fix: clean the dispenser and power-cycle for 1–5 minutes.

• Whirlpool F9E1 Error Code - Causes & Fix

  8 Jun, 2026

  F9E1 means long drain time or unable to drain. Check drain hose installation first: it should not be inserted >4.5 in. into standpipe.

• Whirlpool Washer F8E1 Error Code - Causes & Fix

  8 Jun, 2026

  F8E1 means your Whirlpool washer isn't detecting enough incoming water. Most often it's a closed supply valve or clogged inlet screen.

• Whirlpool F5E3 Error Code - Causes & Fix

  8 Jun, 2026

  F5E3 means the control doesn't see the lid locked. Most often a faulty lid lock assembly. Power-cycle first, then check lock & wiring.

• Whirlpool F7E1 Error Code - Causes & Fix

  8 Jun, 2026

  F7E1 means motor speed sensing fault. Most often shipping bolts still installed or shift actuator failed. Reset and check load first.

• Whirlpool Washer F5E2 Error Code - Causes & Fix

  8 Jun, 2026

  F5E2 means the door or lid lock won't engage. Most often an obstruction or failed lock assembly. Clear debris, power-cycle, or replace lock.

• Whirlpool F5E1 Error Code - Causes & Fix

  8 Jun, 2026

  F5E1 means the door switch or lid lock is not detected as closed. Most often the door is obstructed or the lock assembly has failed.

• Whirlpool F3E1 Error Code - Causes & Fix

  8 Jun, 2026

  F3E1 means the washer cannot detect water level. The most common fix is clearing a clogged or kinked pressure hose or air dome.

• Whirlpool Washer F3E2 Error Code - Causes & Fix

  8 Jun, 2026

  F3E2 means a water-temperature sensor fault. Most often a broken sensor wire or failed thermistor. Check wiring first, then swap sensor.

• Whirlpool Washer F21 Error Code - Causes & Fix

  8 Jun, 2026

  F21 means drain problem or drain time too long. Most often caused by a kinked drain hose or clogged pump filter. Check hose first.

• Whirlpool Washer F2E1 Error - Causes & Fix

  8 Jun, 2026

  F2E1 means a stuck key or user interface fault. Most often a stuck button or failed keypad. Unplug 5 minutes to reset first.

• Whirlpool Washer F20 Error Code - Causes & Fix

  8 Jun, 2026

  F20 means insufficient water supply. Most often caused by closed faucets or clogged inlet screens. Check faucets, hoses, and screens first.

• Whirlpool F1E2 Error Code - Causes & Fix

  8 Jun, 2026

  F1E2 on Whirlpool means different things by product: control-panel fault (washers) or UL A/D error (ovens). Often fixed by a 5-minute reset.

• Whirlpool F1E1 Error Code - Causes & Fix

  8 Jun, 2026

  F1E1 on Whirlpool means a control fault. Power-reset first: unplug or flip the breaker for 5 minutes then test again.