Skip to content
Industrial Error Code Fixes
Go back

Kohler 7410 Generator ECU Fault Codes: SPN/FMI List

⚡ Quick Answer

Kohler generator with a DSE 7410 controller showing ECU Warning, ECU Shutdown or ECU Data Fail? SPN and FMI fault code list from Kohler TP-6985, DSE alarm meanings, and fixes.

⚡ AT A GLANCEScroll down for full repair guide
What it meansOn a Kohler generator fitted with a Deep Sea DSE7410 controller, ECU fault codes are J1939 diagnostic trouble codes from the engine ECU, shown as an SPN (which sensor or circuit) plus an FMI (what went wrong), with a text message on the 7410 display.
Most likely causeMost ECU warnings are a sensor or wiring fault (FMI 3 and 4, out of range high or low), a real engine condition (FMI 0 and 1, extremely high or low), or a lost CAN link between the ECU and the 7410 (ECU Data Fail).
First checkOpen Engine DTCs on the 7410, write down SPN, FMI and occurrence count, match SPN to the component in the table, then check that sensor, its wiring and the physical reading (oil, coolant, fuel) before clearing.
⏱Repair time10-20 minutes to read and interpret the code; 30-90 minutes for a sensor, harness or CAN termination repair
🔧Part neededEngine oil pressure sender, coolant temperature sensor, 120 ohm CAN terminating resistor, DSE7410 controller, fuel filter and water separator

Parts to price first

Check the part before you book service.

Engine oil pressure sender (J1939 engine)

SPN 100 faults with FMI 3 or 4 almost always trace to the sender or its two-wire connector.

$30-$120Check price

Coolant temperature sensor

For SPN 110 out-of-range codes; confirm with an infrared thermometer before replacing.

120 ohm CAN bus terminating resistor

ECU Data Fail on the 7410 is often a missing or failed terminator; the bus should read about 60 ohms between CAN H and CAN L with power off.

DSE7410 MKII controller

Replace only after the engine ECU, harness and CAN wiring check out.

$900-$1,800Check price

Fuel filter and water separator element

Clears SPN 97 Water-in-fuel and many SPN 94 low fuel pressure warnings.

Nature's Generator solar / battery backup (no-engine alternative)

For light backup loads, a solar-charged battery generator has no carburetor, oil, or starter to fault. Price one before the third repair call on an old portable.

Kohler engine service manual download (eManualOnline)

The full OEM-style workshop manual has the wiring diagram, test values, and the fault table this guide summarizes. Instant PDF download.

Repair intent

Need this fixed instead of diagnosed?

Kohler generator with a DSE 7410 controller showing ECU Warning, ECU Shutdown or ECU Data Fail? SPN and FMI fault code list from Kohler TP-6985, DSE alarm meanings, and fixes.

Kohler 7410 Generator ECU Fault Codes: What You Are Looking At

A Kohler generator with a “7410” controller is using a Deep Sea Electronics DSE7410 (or DSE7410 MKII) auto start module. When the controller shows ECU Warning, ECU Shutdown or ECU Data Fail, the alarm did not originate in the 7410. The engine’s own Electronic Control Unit raised a J1939 diagnostic trouble code and passed it over the CAN link. The DSE7410 operator manual describes the display: press the instrument button to access the list of current active Engine DTCs; “the code interpreted by the module shows on the display as a text message. Additionally, the manufacturer’s code is shown.” DSE then tells you to refer to the engine manufacturer’s ECU instructions for the meaning.

Those instructions, for Kohler gensets built on the 4.5 L OEM diesel engines, are Kohler publication TP-6985 (the engine operator’s manual, DTC section 70). This guide pulls the SPN list and FMI list from that manual so you can decode the number on the 7410 screen.

Jump to the SPN table | Jump to the FMI table

How a J1939 ECU Code Is Built

Kohler TP-6985 states that stored and active diagnostic trouble codes are output “according to the J1939 standard as a two-part code”. The first part is a Suspect Parameter Number (SPN) followed by a Failure Mode Identifier (FMI). The manual’s own example: combining SPN 000110 with FMI 03 yields “engine coolant temperature input voltage too high”, with the corrective action “check sensor and wiring”.

So every ECU code on the 7410 answers two questions:

  1. SPN: which circuit or measurement? (oil pressure, coolant temperature, injector 3, EGR valve, DEF tank level, and so on)
  2. FMI: what is wrong with it? (extremely high, out of range low, loss of communication, condition exists, and so on)

Read both. SPN 100 FMI 1 (oil pressure extremely low) is an engine problem. SPN 100 FMI 4 (oil pressure signal out of range low) is a wiring or sender problem on the same circuit.

DSE7410 ECU Alarms and What They Do

The DSE7410 operator manual lists these CAN engine alarms. Type decides whether the set keeps running.

7410 displayTypeDSE manual descriptionFirst check
ECU Warning / CAN ECU WarningWarningThe engine ECU has detected a warning alarm and has informed the DSE module of this situationOpen Engine DTCs, record SPN and FMI
ECU ShutdownShutdownThe engine ECU has detected a shutdown alarm and has informed the DSE module of this situationOil level and pressure, coolant level and temperature, then the DTC
ECU Data FailShutdownThe module is configured for CAN operation and does not detect data on the engine CAN datalink, the engine shuts downECU fuse and power, CAN H/CAN L wiring, terminating resistors
Amber WarningWarningThe CAN ECU has detected a Amber warningNon-critical engine DTC, read it before the next run
Red ShutdownShutdownThe CAN ECU has detected a Red ShutdownCritical engine DTC, do not restart until read
MalfunctionConfigurableThe CAN ECU has detected a Malfunction messageEmissions related DTC on Tier 4 engines
ProtectConfigurableThe CAN ECU has detected a Protect messageEngine is protecting itself, usually derating
Water in FuelConfigurableThe ECU has detected water in the fuelDrain the separator, replace the element
After TreatmentConfigurableThe ECU has detected “After Treatment alarm”DPF, DEF or SCR DTC, see SPN 3xxx and 4xxx

SPN Table (Kohler TP-6985, Section 70) {#spn-table}

TP-6985 notes that “Not all of these codes are used in all engine applications” and that not all DTCs are listed, so an SPN you cannot find here needs the application technical manual. Likely cause and fix columns are added by us; the SPN and description columns are the manual’s wording.

SPNDescription (TP-6985)Likely causeFix
27EGR Valve Position SignalPosition sensor or EGR valve stuckCheck valve movement and sensor wiring
51Air Throttle Actuator Position SignalThrottle actuator or feedback circuitCheck actuator connector, see also SPN 3464
94Low Pressure Fuel Pressure SignalFuel restriction, lift pump, sensorReplace filters, check lift pump, then sensor
97Water-in-fuel SignalWater in the separator bowlDrain and replace the separator element
100Engine Oil Pressure SignalLow oil, sender, wiringCheck oil level, then sender and connector
101Crankcase PressureBlocked breather, worn ringsCheck breather and filter
102Manifold Air Pressure SignalMAP sensor, boost leakCheck for boost leaks, then sensor
103VGT Speed SignalTurbo speed sensorCheck sensor and wiring
105Manifold Air Temperature SignalMAT sensor circuitCheck sensor and wiring
107Air Filter Pressure DifferentialAir filter restrictedReplace the air filter
108Barometric Pressure SignalECU internal sensorECU power and ground, then ECU
109Engine Coolant Pressure SignalCoolant pressure sensorCheck sensor and coolant level
110Engine Coolant Temperature SignalOverheating, sensor, wiringCheck coolant, radiator, fan, then sensor
111Engine Coolant Level Alarm SwitchLow coolant or level switchTop up coolant, check switch
157Fuel Rail Pressure SignalRail pressure sensor, HP pump, PCVCheck for fuel starvation first
158ECU Power DownECU lost power improperlyCheck battery and keep-alive supply
168Unswitched Battery VoltageBattery, charger, loose cablesLoad test battery, check alternator
174Fuel Temperature SignalFuel temp sensorCheck sensor and wiring
189Engine Speed DerateECU is derating for another DTCFix the other active codes
190Engine SpeedCrank or cam signal, overspeedSee SPN 636 and 637
412EGR Temperature SignalEGR temp sensorCheck sensor and wiring
611, 612Injector Drive #1, #2Injector driver circuit in ECUCheck injector harness, then ECU
613Fuel Pressure Control Valve DrivePCV driver circuitCheck PCV connector and wiring
629ECU EEPROMECU memory faultECU replacement or reflash by dealer
636Camshaft Position SignalCam sensor, wiring, timingCheck sensor gap and wiring
637Crankshaft Position SignalCrank sensor, wiring, flywheelCheck sensor gap and wiring
651 to 656Injector #1 to #6Injector open, short, or harnessCheck resistance at the injector and harness
695Unapproved Engine Speed RequestSpeed command outside allowed rangeCheck 7410 speed settings and CAN configuration
970External Shutdown SwitchShutdown input activeCheck E-stop and external shutdown wiring
1075Low Pressure Fuel Pump DataLift pump feedbackCheck pump power and connector
1136ECU Temperature SignalECU running hotCheck mounting, airflow, enclosure temperature
1172Intake Air TemperatureIAT sensorCheck sensor and wiring
1176Intake Air PressureIntake pressure sensorCheck sensor and intake leaks
1180Calculated VGT Turbine Inlet TempCalculated value out of rangeCheck exhaust temp and turbo DTCs
1209Exhaust Manifold Pressure SignalExhaust pressure sensorCheck sensor tube for soot blockage
1347, 1348Fuel Pump Pressure Control Valve 1, 2PCV circuitCheck valve connector and wiring
1321Engine Starter Control CircuitStarter relay or circuitCheck starter relay and wiring
1569Engine Power DerateECU derating for another DTCFix the other active codes
1761DEF Tank Fuel Level SignalDEF level sensor or empty tankFill DEF, then check sensor
2629, 2630, 2790Turbo compressor and charge air cooler outlet temperatureTemperature sensor or charge air issueCheck sensors, CAC for blockage
2659EGR Flow SignalEGR flow out of rangeCheck EGR valve, cooler, sensors
2791EGR Valve Drive CircuitEGR actuator circuitCheck actuator connector
2795VGT Calibration VersionTurbo actuator calibration mismatchDealer recalibration
2797, 2798Injector High Voltage Supply #1, #2Injector supply inside ECUCheck harness for shorts, then ECU
3031DEF Tank Fluid Temp SignalDEF temp sensorCheck sensor and header unit
3216, 3226DPF Outlet NOx, SCR Outlet NOxNOx sensorCheck sensor connector and power
3246, 3251DPF Outlet Temperature, DPF Differential Pressure SignalAftertreatment sensorsCheck sensor tubes and connectors
3361DEF Dosing Injector SignalDosing injector circuitCheck injector connector
3464Air Throttle Actuator Drive CircuitThrottle actuator circuitCheck actuator connector and wiring
3509 to 3514, 5125 to 5127Sensor Supply #1 to #9 VoltageA sensor reference supply is shortedUnplug sensors one at a time to find the short
3516, 3517Aftertreatment DEF Concentration, DEF Tank Fluid LevelDEF quality or levelUse fresh DEF, fill the tank
3597Injector Power Supply VoltageInjector supply voltageCheck battery voltage and ECU power
3719, 3720, 3936Calculated Soot Level, Calculated Ash Level, DPF Fault OccurrencesDPF loadingRun regeneration, service the DPF
4334, 4341, 4343, 4345, 5435, 5745DEF Dosing Unit Outlet Pressure, Pressure line Heater, Supply Line Heater, Return Line Heater, Pump, HeaterDEF dosing unit componentsCheck DEF supply, heaters and dosing unit
4360, 4363, 4364, 4366SCR Inlet Temperature, SCR Outlet Temperature, SCR Catalyst Conversion Efficiency, DEF Tank Heater Coolant ValveSCR sensors and DEF tank heatingCheck sensors, DEF quality, heater valve
4376Reversing ValveDEF reversing valveCheck valve and dosing unit
4490Intake Air HumidityHumidity sensorCheck sensor
4765, 4766, 5018, 5298DOC Inlet and Outlet Temp, DOC Fault Occurrences, DOC EfficiencyDiesel oxidation catalystCheck sensors, DOC condition
4795DPF MissingDPF not detectedConfirm DPF fitted and sensors connected
5571HPCR Pressure Relief ValveRail relief valve openedCheck rail pressure DTCs, PCV
5743SCR Temperature ModuleSCR temp moduleCheck module power and CAN
522494, 522495Intake Air Sensor Communication, Exhaust Filter Temp ModuleModule communication lostCheck module power and CAN wiring

FMI Table (Kohler TP-6985) {#fmi-table}

FMINameWhat it usually means
0Extremely HighReal reading above the shutdown limit
1Extremely LowReal reading below the shutdown limit
2InvalidData erratic or intermittent
3Out of Range HighSensor voltage high: open circuit or short to supply
4Out of Range LowSensor voltage low: short to ground
5High ResistanceOpen circuit or corroded connector
6Low ResistanceShort circuit
7MismatchMechanical response does not match command
8Signal MissingNo signal frequency or period
9Loss of CommunicationModule not responding on the bus
10Change AbnormalRate of change too fast or slow
11ActivatedComponent activated by a fault
12ErrorBad device or component
13FaultOut of calibration
14Incorrect MessageSpecial instructions
15Slightly HighAbove normal, least severe
16Moderately HighAbove normal, moderate
17Slightly LowBelow normal, least severe
18Moderately LowBelow normal, moderate
19Communication ErrorReceived network data in error
31Condition ExistsFault present, no further detail

Fix Tree

1. ECU Data Fail or no DTC list at all

  1. Check the ECU fuse and that the ECU has battery voltage with the key on.
  2. With power off, measure between CAN H and CAN L at the 7410 connector. About 60 ohms means both terminators are present; 120 ohms means one is missing; open means a broken wire.
  3. Inspect the CAN harness between the ECU and the controller for chafing, pinched wires and corroded pins.
  4. Confirm the engine type selected in the 7410 configuration matches the ECU.

2. ECU Warning with an FMI of 3, 4, 5 or 6

This is a circuit fault, not an engine condition. Find the SPN in the table, go to that sensor, unplug it, and check the connector for corrosion and bent pins. Measure the sensor resistance or voltage against the engine service data. Repair wiring before replacing a sensor.

3. ECU Shutdown with an FMI of 0 or 1

The engine saw a real extreme value. For SPN 100 check oil level and pressure with a mechanical gauge. For SPN 110 check coolant level, the radiator, fan belt and thermostat. For SPN 190 check for an overspeed event and the governor. Only after the physical check passes should you suspect the sensor.

4. Derate codes (SPN 189, 1569) or aftertreatment codes (SPN 3xxx to 5xxx)

The ECU is protecting the engine or the emissions system. Read every active DTC, fix the root one, and run the regeneration or DEF service the engine manual calls for. These codes rarely clear by resetting the 7410.

5. Resetting

Press Stop/Reset on the 7410 to clear the module alarm after the repair. The DSE manual notes that pressing the button on a suitably configured engine ECU cancels passive alarms on the ECU. Stored DTCs that remain in the ECU need the engine manufacturer’s service tool. TP-6985 adds that the instrument panel may also display text for communication faults such as “CAN Bus FAILURE”, which should go to the servicing dealer.

When to Call a Professional

Call a Kohler or engine dealer for injector driver and high voltage supply codes (SPN 611, 612, 2797, 2798), ECU EEPROM (SPN 629), VGT calibration (SPN 2795), and any aftertreatment code that returns after a forced regeneration. These need the dealer service tool to test, recalibrate or reflash.

Need Replacement Parts?

Confirm the engine model on the nameplate and the SPN on the 7410 before ordering. Check oil pressure senders, coolant sensors, CAN terminators and DSE7410 controllers on Amazon - prices and availability change frequently.

Quick FAQ

What does ECU Warning mean on a Kohler 7410 generator controller?

The DSE7410 manual states that ECU Warning means the engine ECU has detected a warning alarm and has informed the DSE module. The engine keeps running. Press the button on the 7410 to open Engine DTCs and read the SPN and FMI behind the warning.

What does ECU Data Fail mean?

ECU Data Fail is a shutdown alarm. The module is configured for CAN operation and does not detect data on the engine CAN datalink, so the engine shuts down. Check the ECU fuse and power, the CAN H and CAN L wiring between the ECU and the 7410, and the 120 ohm terminating resistors.

How do I read a Kohler ECU fault code like SPN 110 FMI 3?

Look up the SPN in the table for the component, then the FMI for the failure type. SPN 110 is Engine Coolant Temperature Signal and FMI 3 is Out of Range High, so the coolant temperature sensor circuit is reading too high a voltage: check the sensor and its wiring.

Can I clear ECU fault codes from the 7410?

You can reset the 7410 alarm with the Stop/Reset button once the cause is fixed. The DTC itself lives in the engine ECU. Active codes return as soon as the fault condition is present again, and stored codes are cleared with the engine maker's service tool.


Share this post on:

Previous Post
Kohler Generator Fault Codes: Meanings and Fixes
Next Post
Cummins Generator Error Codes: Complete Guide