Posts
All the articles I've posted.
-
Navien NPE-A 016 — Overheat Lockout Fix
Code 016 (also displayed as E016) on a Navien NPE-A or NPE-S tankless water heater means the unit's heat exchanger outlet temperature exceeded the overheat...
-
Norlake Walk-In Error Code — Defrost Issue Fix
Norlake commercial walk-in cooler and freezer controllers (typically Heatcraft Beacon II or KE2 Evap Efficiency in newer installs, Danfoss EKC in older)...
-
Okuma OSP Alarm 2202 — Spindle Fix
Okuma OSP control alarm 2202 (formatted as "2202 SPINDLE" or "2202-1" with axis sub-code) indicates the spindle drive amplifier has detected a fault during...
-
Payne Error Code 31 — Pressure Switch Did Not Open Fix
Payne code 31 means the integrated furnace control sees the pressure switch already closed at the start of a heat call, before the inducer has run — the...
-
Pitco Fryer Error Code E6 — High Temp Limit Fix
Pitco commercial fryer error E6 means the high-limit safety switch has opened — oil temperature exceeded the safety threshold (typically 460-475°F). The...
-
Allen-Bradley PowerFlex vs Siemens SINAMICS — An Industrial Tech's Honest Comparison (2026)
For a plant that's already standardized on Rockwell ControlLogix or CompactLogix PLCs and uses EtherNet/IP as its primary fieldbus, buy Allen-Bradley...
-
Samsung vs LG French-Door Refrigerators — An Appliance Tech's Honest Comparison (2026)
If you want a feature-rich French-door refrigerator with the most-developed smart-home integration and a generally lower service-call rate over 5-8 years,...
-
Schneider Altivar OCF Fault — Overcurrent Fix
Schneider Altivar OCF (Overcurrent Fault) on the ATV320, ATV340, ATV630, ATV930, and most legacy ATV61/71 drives means the drive's IGBT power module...
-
Schneider Altivar OSF Fault — Overspeed Fix
Schneider Altivar OSF (Overspeed Fault) means the drive's speed feedback (calculated from the back-EMF model in open-loop or from a real encoder in...
-
Scotsman 6-Flash Code — Refrigerant Pressure Out of Range Fix
A 6-flash code on a Scotsman Brilliance-series ice machine means the controller has detected refrigerant pressure outside the expected operating range —...
-
Siemens SINAMICS G120 F30011 Fault — Phase Loss Fix
SINAMICS G120 F30011 (Line Phase Loss) means the Power Module's input phase-monitoring logic detected that one of the three input phases is missing or...
-
Siemens SINAMICS G120 F30021 Fault — Ground Fault Fix
SINAMICS G120 F30021 (Ground Fault) means the Power Module's output current sensors saw an imbalance — current flowing out the U, V, W phases summed to a...
-
Sub-Zero Refrigerator Error Code EC — Evap Fan Fix
Sub-Zero refrigerators display "EC" (sometimes shown as "EC 38" or "EC 39" with sub-code) when the main control board detects an evaporator fan circuit...
-
Takagi Code 111 — No Ignition Fix
Code 111 on a Takagi tankless water heater (T-H3, T-H3J, T-K4, T-D2, T-KJr2, T-M50, and the newer Tx2 condensing platforms) means the unit attempted...
-
Tempstar 4-Flash Error Code — Limit Switch Fix
A Tempstar 4-flash code means the integrated furnace control opened the gas valve on a heat call, but a high-limit safety switch (either the primary heat...
-
Trane 3-Blink Error Code — Pressure Switch Fault Fix
A 3-blink fault on a Trane furnace LED means the integrated furnace control did not see the pressure switch close after the inducer started, or...
-
Trane XV20i/XV18 Fault 126 — Low Pressure Cutout Fix
Fault 126 on a Trane XV20i, XV18, or XL20i variable-speed heat pump means the outdoor unit's low-pressure switch opened — refrigerant suction pressure...
-
Trane Voyager RTU Error Code 31 — Fix
Trane Voyager rooftop unit (RTU) error code 31 on the UCM (Unit Control Module) or Tracer SC controller indicates a high-pressure cutout — the...
-
Viking Range Error Code F0 — Control Board Fault Fix
Viking range error F0 (sometimes shown as "F-0" or just blinking "F" on older models) indicates the electronic oven control (EOC) has detected an internal...
-
Vulcan/Wolf Convection Oven F-Code Error — Gas Oven Fix
Vulcan and Wolf (commercial Wolf, not residential Sub-Zero Wolf) gas convection ovens display F-series error codes (F1 through F9 depending on model) when...
-
Weil-McLain Code 1 — No Flame Sensed Fix
Code 1 on a Weil-McLain Gold or Ultra Series boiler means the boiler attempted ignition but did not prove flame within the trial-for-ignition window...
-
Weil-McLain Code 3 — Low Water Cutoff Fix
Code 3 on a Weil-McLain Gold or Ultra Series boiler (Ultra 80/105/155/230/310/399, GV90+, and WM97+ platforms) indicates a low water cutoff (LWCO) lockout —...
-
Yaskawa GA800 oC Fault — Overcurrent Fix
Yaskawa GA800 oC (Overcurrent) means the output current sensors on at least one of the U, V, or W phases saw current exceed roughly 200% of the drive's...
-
Yaskawa GA800 oV Fault — DC Overvoltage Fix
Yaskawa GA800 oV (DC Overvoltage) means the internal DC bus climbed above approximately 820 VDC on a 480V-class drive (or 410 VDC on a 240V-class) while the...