Tag: appliance
All the articles with the tag "appliance".
-
LG Dryer D90 Error Code - Causes & Fix
D90 means 90% duct blockage. Clean the lint filter, check the exterior vent hood for clogs, and inspect the flex hose for kinks.
-
LG Dryer D80 Error Code - Causes & Fix
D80 means about 80% airflow restriction in the exhaust vent. Clean the entire vent run from lint screen to exterior hood first.
-
LG Dryer D75 Error Code - Causes & Fix
D75 means 75% exhaust blockage. Clean lint from the entire vent run, check for crushed ducts, and verify air blows outside.
-
LG Dryer Add Error Code - Causes & Fix
Add means add water to the steam feeder. Fill the drawer to the MAX line with tap water and close it fully. Problem solved in 1 minute.
-
LG Dishwasher tE Error Code - Causes & Fix
tE means the control board detected a faulty temperature sensor signal. Most often a failed thermistor is to blame. Replace the sensor.
-
LG Dishwasher PE Error Code - Causes & Fix
PE on an LG dishwasher means a water level sensor fault. The most common fix is replacing the defective sensor or repairing its wiring.
-
Samsung HR Error Code - Causes & Fix
HR means heater error on Samsung washers. Most often caused by reversed hot/cold hoses. Swap hoses so hot supply connects to hot inlet.
-
Samsung Washer bE4 Error Code - Causes & Fix
bE4 can mean unbalanced load or water-supply fault depending on your model. Most often a kinked hose or closed tap; check supply first.
-
Samsung Washer dE2 Error Code - Causes & Fix
dE2 means door not latched or lock not confirming (varies by model). Most often: laundry caught in door or loose strike. Close firmly & retry.
-
Samsung bE0 Error Code - Causes & Fix
Samsung bE0 means a control-panel button is stuck or continuously pressed. Free stuck buttons and clean moisture from the keypad first.
-
Samsung Microwave C-d1 Error Code - Causes & Fix
C-d1 means the door lock or sensor is not detecting a closed position. Most often a faulty door latch or lock switch. Power-cycle first.
-
LG Dishwasher OE Error Code - Causes & Fix
OE means drainage failure. Water remains in the tub. Most often: clogged filter or kinked drain hose. Clean filters and check the hose.
-
LG Dishwasher nE Error Code - Causes & Fix
nE means vario motor error (spray function fault). Most often a failed vario motor. Check wiring and test motor resistance first.
-
LG Dishwasher LE Error Code - Causes & Fix
LE means motor error on LG dishwashers. Most often caused by a failed wash motor or debris blocking the pump. Reset power first.
-
LG Dishwasher IE Error Code - Causes & Fix
IE means the dishwasher did not fill with enough water within 30 seconds to 10 minutes. Check the water shutoff valve under the sink first.
-
LG Dishwasher HE Error Code - Causes & Fix
HE means heating error. The dishwasher cannot heat water. Most often the heating element or thermistor has failed. Reset first, then check.
-
LG Dishwasher FE Error Code - Causes & Fix
FE means Fill Error: the dishwasher detected abnormal water fill. Check float assembly for stuck debris, then inspect inlet valve.
-
LG Dishwasher E1 Error Code - Causes & Fix
E1 means a leak or overfill triggered the float switch. Most often water pooled in the base pan from a door seal or internal leak.
-
LG Dishwasher CR Error Code - Causes & Fix
CR means your LG dishwasher is stuck in Test Mode (Continuous Run). Turn the unit off at the breaker for 30 seconds, then power back on.
-
LG Dishwasher CE Error Code - Causes & Fix
CE is a motor error on LG dishwashers. The wash motor or its wiring harness has failed. Reset power, check connections, replace motor if needed.
-
LG Dishwasher bE Error Code - Causes & Fix
bE means bubble error: too many suds. Fix: confirm you're using dishwasher detergent (not dish soap), run empty cycle to clear foam.
-
LG Dishwasher AE Error Code - Causes & Fix
AE means water in the base pan triggered the leak sensor. Most often caused by a dirty door gasket. Dry the pan and find the leak source.
-
Samsung Washer UC Error Code - Causes & Fix
UC means power supply or voltage problem. Most often caused by unstable line voltage or using an extension cord. Plug directly into a dedicated circuit.
-
Samsung Washer UB Error Code - Causes & Fix
UB means unbalanced load. The drum is weighted to one side during spin. Pause, untangle and redistribute laundry, then restart.