Tag: appliance

All the articles with the tag "appliance".

• LG Microwave F13 Error Code - Causes & Fix

  7 Jun, 2026

  F13 on an LG microwave signals a voltage error. LG requires a service call. The most common cause is a power-supply or control-board fault.

• LG Microwave F11 Error Code - Causes & Fix

  7 Jun, 2026

  F11 means inverter communication error on LG microwaves. Most often caused by a failed inverter board or loose connector.

• LG Microwave F1 Error Code - Causes & Fix

  7 Jun, 2026

  F1 on an LG microwave means a mainboard problem. The most common fix is replacing the main control board, which requires service.

• LG Microwave F-5 Error Code - Causes & Fix

  7 Jun, 2026

  F-5 means damper switch error. Check for door obstructions (packing, racks). If clear and code persists, call service for switch.

• LG Microwave F-3 Error - Causes & Fix

  7 Jun, 2026

  F-3 means a control panel or touch button problem. Clean the keypad, power-reset, and replace the panel if the code persists.

• LG Microwave F-2 Error Code - Causes & Fix

  7 Jun, 2026

  LG F-2 means the thermistor reports out-of-range temperature. Most likely: failed thermistor or loose connector. Service required.

• LG Microwave F-11 Error Code - Causes & Fix

  7 Jun, 2026

  F-11 means inverter communication error on LG microwaves. The inverter board is the most likely culprit. Requires service.

• LG Microwave E10 Error Code - Causes & Fix

  7 Jun, 2026

  E10 means an internal short in the control board. Most often the board itself has failed and needs replacement after a power reset.

• LG Microwave DOOR Error - Causes & Fix

  7 Jun, 2026

  DOOR means the microwave detects the door is not fully closed or latched. First clear any debris or packing material and close firmly.

• LG Dryer tE3 Error Code - Causes & Fix

  7 Jun, 2026

  tE3 means your LG dryer detected a thermistor (temperature sensor) fault. Most common fix: power-reset the dryer, then replace the thermistor.

• LG Dryer tE2 Error Code - Causes & Fix

  7 Jun, 2026

  tE2 means the thermistor (temperature sensor) is reading out of range. Most often caused by cold air backdraft through the vent in winter.

• LG Dryer tE1 Error Code - Causes & Fix

  7 Jun, 2026

  tE1 means the dryer detected a thermistor fault. Most often a failed sensor or loose connector. Reset power first, then check airflow.

• LG Dryer tE Error Code - Causes & Fix

  7 Jun, 2026

  tE or tE1 means the thermistor temperature sensor has failed or lost signal. Most often the thermistor itself needs replacement.

• LG Dryer PS Error Code - Causes & Fix

  7 Jun, 2026

  PS means improper voltage at the power cord connection. Most often the white and red wires are reversed on the terminal block.

• LG Dryer nP Error Code - Causes & Fix

  7 Jun, 2026

  nP means no current detected at the heater, usually from a tripped breaker or lost 240 V leg. Reset the double-pole breaker fully off 10 sec.

• LG Dryer LE2 Error Code - Causes & Fix

  7 Jun, 2026

  LE2 on LG dryers means a compressor fault on heat-pump models or motor/airflow issues on standard models. Reset power first.

• LG Dryer HS Error Code - Causes & Fix

  7 Jun, 2026

  HS means humidity sensor error. Clean the sensor bars inside the drum below the lint filter, then reset. Most common fix.

• LG Dryer HE Error Code - Causes & Fix

  7 Jun, 2026

  HE on an LG washer-dryer combo means temporary heater error. Power off, unplug, wait, retry. If it repeats, schedule service.

• LG Dryer F0 Error Code - Causes & Fix

  7 Jun, 2026

  F0 means the lint filter is out, not fully seated, or not detected. Reseat the filter firmly and clean the housing to clear the code.

• LG Dryer E4 Error Code - Causes & Fix

  7 Jun, 2026

  E4 is not a standard LG dryer code. Your display likely shows dE4 (door switch fault). Check for obstructions and close the door firmly.

• LG Dryer E13 Error Code - Causes & Fix

  7 Jun, 2026

  E13 on LG hybrid condensing dryers means a condensate drain problem. Most often a kinked or clogged drain hose. Fix by straightening the hose.

• LG Dryer E1 Error Code - Causes & Fix

  7 Jun, 2026

  E1 (tE1) means a thermistor fault. Most often a failed temperature sensor or loose connector. Reset power first, then check sensor.

• LG Dryer E00 Error Code - Causes & Fix

  7 Jun, 2026

  E00 means the display PCB cannot read software from the main control board. Unplug for 60 seconds and restart-if it returns, a board is faulty.

• LG Dryer D95 Error Code - Causes & Fix

  7 Jun, 2026

  D95 means 95% airflow blockage in the exhaust duct. Clean the lint filter and check the outside vent for obstructions or clogs.