Skip to content
Industrial Error Code Fixes
Go back

Rinnai V65iN Error Codes - Guide to Codes 10, 11, 12, 14, LC

⚡ Quick Answer

A complete guide to troubleshooting Rinnai V65iN error codes. Learn what codes 10, 11, 12, 14, 16, LC and others mean and how to fix them fast.

⚡ AT A GLANCEScroll down for full repair guide
What it meansIgnition failure, flame loss, overheating, or scale buildup
Most likely causeGas supply issues, blocked vents, dirty sensors, or mineral deposits
First checkCheck gas valve, inspect vent pipes for blockages, clean flame rod
⏱Repair time20 minutes to 2 hours
🔧Part neededFlame rod, igniter, water flow sensor, condensate neutralizer, descaling kit

Parts to price first

Check the part before you book service.

Rinnai Flame Rod/Igniter Assembly

Replacement flame sensor rod and igniter assembly to fix ignition and flame loss codes (11, 12).

Tankless Water Heater Descaling Kit

Kit with pump and hoses to flush the heat exchanger and clear LC codes.

Water Flow Sensor Assembly

Measures water flow to activate the heater; replacement can solve intermittent heating issues.

Condensate Neutralizer Kit

For condensing models, this kit neutralizes acidic condensate before it enters the drain.

Water heater repair parts (Mobile Home Parts Store)

Elements, thermostats, thermocouples, gas valves, and anode rods in stock when the local supply house is closed.

Repair intent

Need this fixed instead of diagnosed?

A complete guide to troubleshooting Rinnai V65iN error codes. Learn what codes 10, 11, 12, 14, 16, LC and others mean and how to fix them fast.

Rinnai’s V65iN tankless water heaters are known for efficiency, but an error code on the display can bring your hot water supply to a halt. This guide will walk you through the most common Rinnai error codes, explaining what they mean and how you can troubleshoot them to restore your hot water.

Source: Rinnai Troubleshooting TWH Diagnostic Codes, Document 100000652, https://media.rinnai.us/salsify_asset/s-d7680150-5ee9-4b1f-9f19-b4e6be7a41c4/100000652-Troubleshooting%20TWH%20Diagnostic%20Codes%20(1).pdf

Jump to Fix

Rinnai V65iN Error Codes - What They Mean

When your Rinnai V65iN detects an issue, it will flash a two-digit code on the temperature controller or a service monitor. This isn’t a sign of failure - it is a diagnostic tool. The code tells a technician (or you) exactly where to start looking for the problem, saving time and money. The most frequent codes relate to problems with ignition, flame, venting, or a buildup of mineral scale.

This guide focuses on the codes specified for the V65iN model, ensuring you get accurate, model-specific advice.

V65iN Common Fault Code Reference

CodeMeaning
10Air Supply or Exhaust Blockage
11Ignition Failure
12Flame Failure
14Thermal Fuse Open / Overheating
16Over-Temperature Safety Limit Exceeded
19Electrical Grounding / Wiring Fault
32Outgoing Water Temperature Sensor Fault
52Modulating Solenoid Valve Circuit Fault
61Combustion Fan Motor Fault
65Water Flow Control Servo Fault
71Gas Solenoid Valve Circuit Fault
72Flame Sensing Device Fault
LCScale Buildup in Heat Exchanger

Common Causes by Fault

Code 10 (Venting Issue): This code means the heater is not getting enough air or cannot properly exhaust fumes. Check the exterior vent terminations for blockages like leaves, snow, or insect nests. Bird screens can prevent this.

Codes 11 & 12 (Ignition & Flame Failure): Code 11 means the unit never lit, while Code 12 means the flame went out during operation. Common causes include no gas supply (check your meter and other gas appliances), air in the gas line, or a dirty flame rod/igniter assembly. The flame rod is a safety device that confirms a fire is present; if it’s coated in soot, it can’t do its job.

Codes 14 & 16 (Overheating): These are serious safety codes indicating the water has gotten too hot inside the unit. The number one cause is mineral scale buildup inside the heat exchanger, which restricts water flow and blocks heat transfer. A clogged water filter or an obstructed vent can also cause overheating.

Code LC (Lime/Calcium Buildup): This is not a fault but a maintenance reminder. It is telling you that scale has accumulated in the heat exchanger and it’s time to perform a descaling flush. Ignoring this code will eventually lead to an overheating fault (Code 14 or 16).

Step-by-Step Fix {#fix}

Step 1: Reset the Unit. The first step for any code is a simple reset. Turn off all your hot water faucets. Press the “On/Off” button on your Rinnai controller to power the unit down. Wait 30 seconds, then press the “On/Off” button again to power it back on. For many transient faults, this is all that is needed.

Step 2: Check Gas and Power (Code 11). If an ignition failure code persists, confirm your gas supply is active. Check the gas valve at the heater, your main gas meter, and any other gas appliances in your home. If you recently had a gas outage, there may be air in the line that needs to be purged.

Step 3: Inspect Vents (Code 10). Go outside and visually inspect the intake and exhaust vent pipes. Clear away any debris, snow, or other obstructions. A blocked vent starves the unit of the air it needs for safe combustion.

Step 4: Clean the Flame Rod (Code 12). For a recurring flame failure, cleaning the flame rod is a common fix. After shutting off power and gas, you can access the flame rod in the burner chamber. Carefully remove it and gently clean the metal rod with fine steel wool until it is shiny. Do not use sandpaper, as this will damage the surface.

Step 5: Descale the Heat Exchanger (Code LC, 14, 16). This is the most important maintenance task for a tankless heater. Using a descaling kit (a small pump, hoses, and a bucket) and a few gallons of white vinegar, circulate the solution through the heater via the service valves for about 45-60 minutes. This dissolves the mineral deposits and restores flow and efficiency.

Parts Often Needed

Flame Rod / Igniter: This is often a single assembly. Over time, the flame rod can degrade and fail to sense the flame properly, leading to Code 12 faults. They are a common replacement part.

Descaling Kit: An essential tool for any tankless owner. Regular descaling prevents the majority of overheating issues and extends the life of the heater.

Water Flow Sensor: This part tells the heater when you have turned on a hot water tap. If it fails, the heater may not turn on or may behave erratically.

Technician Tips

Always clean the small, inline water filter screen at the cold water inlet. A clogged screen restricts flow and can lead to overheating or low hot water pressure.

If you are getting repeated ignition failures (Code 11) and the igniter is glowing but the gas does not light, the issue could be low gas pressure. This requires a technician with a manometer to measure and adjust the pressure.

For any codes related to internal circuit boards or gas valves (52, 70, 71), a reset is the only DIY step. If the code returns, it indicates a component failure that requires professional service.

When to Call a Pro

Do not attempt to work on the gas line or measure gas pressure yourself. These tasks require specialized tools and training and should only be performed by a licensed plumber or gas technician.

If you have cleaned the flame rod and continue to get a Code 12, or if you have descaled the unit and still get a Code 16, it is time to call a professional. The issue may be a failing gas valve, a faulty fan motor, or a bad sensor that requires expert diagnosis.

Any electrical codes, like Code 19, or circuit board codes (70, 71, 72) that are not resolved with a power cycle, point to a problem that needs a certified Rinnai technician.

Quick FAQ

What does code 11 on my Rinnai V65iN mean?

Error code 11 on a Rinnai V65iN means the unit failed to ignite. The most common causes are an unopened gas valve, air in the gas line, or a dirty or faulty igniter. Ensure all gas valves are fully open before trying to reset the unit.

How do I fix a Rinnai code 12 flame failure?

Code 12 indicates the flame went out while the unit was running. This is often caused by a dirty flame rod that cannot properly sense the flame. You can often fix this by cleaning the flame rod with fine steel wool. Other causes include incorrect gas pressure or a venting issue.

What is the Rinnai LC code?

The LC code (or LC0-LC9) is a maintenance reminder indicating it's time to descale the heat exchanger. Mineral deposits have built up inside the unit, and flushing it with a descaling solution is required to restore performance and prevent overheating.

How do I reset my Rinnai water heater?

To reset a Rinnai tankless water heater, simply turn off all hot water faucets, then press the 'On/Off' button on the temperature controller twice - once to turn it off, and again to turn it back on. You can also unplug it from the electrical outlet for 30 seconds.


Share this post on:

Previous Post
Rheem Water Heater Error Codes - LED, EcoNet, Tankless
Next Post
Rinnai Error Code 52 — Outlet Water Temperature Sensor Fault