Skip to content
Industrial Error Code Fixes
Go back

More industrial fault codes

Mitsubishi FR-F700 Fault Codes (E.OC1, E.OV1, E.THT, E.LF Fixes)

⚡ Quick Answer

Troubleshoot Mitsubishi FR-F700 VFD fault codes. This guide explains E.OC1, E.OV1, E.THT, E.THM, E.FIN, E.LF, and other common drive errors.

⚡ AT A GLANCEScroll down for full repair guide
What it meansOvercurrent, overvoltage, overload, overheat, or phase loss faults
Most likely causeIncorrect acceleration/deceleration times, wiring faults, or mechanical overload
First checkCheck the PU (keypad) display for the E.xxx fault code. Inspect wiring and ventilation.
⏱Repair time20 minutes to 2 hours
🔧Part neededCooling fan, keypad (FR-DU07), braking resistor, or replacement drive

Parts to price first

Check the part before you book service.

FR-F700 Cooling Fan

Replacement cooling fan module to prevent E.FIN (heatsink overheat) faults.

FR-DU07 Keypad / PU

Parameter unit (PU) keypad for programming, monitoring, and fault diagnosis.

Dynamic Braking Resistor

External resistor used to dissipate regenerative energy and prevent overvoltage faults.

Mitsubishi FR-F700 Replacement Drive

New or refurbished FR-F700 series VFD when repair is not possible.

Equipment service manual download (eManualOnline)

The full OEM-style workshop manual has the wiring diagram, test values, and the fault table this guide summarizes. Instant PDF download.

Repair intent

Need this fixed instead of diagnosed?

Troubleshoot Mitsubishi FR-F700 VFD fault codes. This guide explains E.OC1, E.OV1, E.THT, E.THM, E.FIN, E.LF, and other common drive errors.

The Mitsubishi FR-F700 series of variable frequency drives (VFDs) are workhorses in many industrial applications, but a fault code on the parameter unit (PU) can bring production to a halt. This guide covers the most common “E.” fault codes, explaining what they mean and how to troubleshoot them effectively.

Source: Mitsubishi FR-F700 Instruction Manual (Applied), IB-0600177ENG. A copy is available at https://dl.mitsubishielectric.com/dl/fa/document/manual/inv/ib0600177eng/ib0600177engf.pdf

Jump to Fix

Mitsubishi FR-F700 Fault Codes - What They Mean

When the FR-F700’s protective functions are triggered, the drive output is shut off, a fault relay is activated, and an error code prefixed with “E.” is displayed on the keypad. These codes pinpoint the exact nature of the problem, allowing for rapid diagnosis and correction. The most common faults relate to overcurrent, overvoltage, and thermal issues.

FR-F700 Common Fault Code Reference

CodeMeaning
E.OC1Overcurrent during Acceleration
E.OC2Overcurrent during Constant Speed
E.OC3Overcurrent during Deceleration
E.OV1Overvoltage during Acceleration
E.OV2Overvoltage during Constant Speed
E.OV3Overvoltage during Deceleration
E.THTInverter Overload (Electronic Thermal)
E.THMMotor Overload (Electronic Thermal)
E.FINHeatsink Overheat
E.ILFInput Phase Loss
E.LFOutput Phase Loss
E.GFGround Fault
E.UVTUndervoltage
E.PEParameter Storage Device Error (EEPROM)
E.CPUCPU Error

Common Causes by Fault

Overcurrent (E.OC1, E.OC2, E.OC3): These are the most frequent faults. They trigger when motor current exceeds the drive’s protective limits. E.OC1 is often caused by an acceleration time (Pr. 7) that is too short for the load’s inertia. E.OC2 points to a sudden load change or mechanical jam. E.OC3 can be caused by a deceleration time (Pr. 8) that is too short. Any of these can also be caused by a short circuit in the motor wiring.

Overvoltage (E.OV1, E.OV2, E.OV3): These faults occur when the drive’s internal DC bus voltage gets too high. This is a common issue with high-inertia loads (like heavy fans or flywheels) during deceleration. The motor acts as a generator, sending power back to the drive. If this regenerative energy is too great, the voltage rises and the drive trips to protect itself.

Overload & Overheat (E.THT, E.THM, E.FIN): These are thermal protection faults. E.THT means the drive’s power module was overloaded. E.THM means the motor was overloaded (based on settings in Pr. 9). E.FIN indicates the drive’s heatsink is too hot, usually due to a failed or blocked cooling fan or high ambient temperature.

Phase Loss (E.ILF, E.LF): These faults indicate a missing electrical connection. E.ILF means one of the incoming power phases (R, S, T) is lost. E.LF means one of the outgoing motor phases (U, V, W) is disconnected. A loose wire is the most common cause.

Step-by-Step Fix {#fix}

Step 1: Record and Identify the Fault. Note the exact fault code displayed on the keypad before doing anything else. Do not immediately reset the drive, as the code provides critical diagnostic information.

Step 2: Inspect Motor Wiring (E.OCx, E.GF). For any overcurrent or ground fault, power down the drive completely (wait for the keypad to go dark). Disconnect the motor leads (U, V, W) at the drive. Use a megohmmeter (megger) to test the insulation resistance of the motor and cables from each phase to ground. It should be at least 5 megohms. Also check for shorts between phases.

Step 3: Adjust Accel/Decel Times (E.OC1, E.OVx). If you are getting overcurrent on acceleration, increase the value in Parameter 7 (Acceleration time). If you are getting overvoltage faults on deceleration, increase the value in Parameter 8 (Deceleration time). This gives the drive more time to ramp the motor speed up or down, reducing current spikes and regenerative energy.

Step 4: Check Ventilation (E.FIN). For a heatsink overheat fault, visually inspect the drive’s cooling fan. Is it running? Is it clogged with dust or debris? Clean the heatsink fins and ensure there is adequate clearance around the drive for proper airflow.

Step 5: Verify Connections (E.ILF, E.LF). For phase loss faults, shut off power and use a screwdriver to check the tightness of all power terminals (R, S, T) and motor terminals (U, V, W). A single loose wire is a very common cause of these faults.

Step 6: Reset the Drive. Once you have investigated and addressed the likely cause, you can reset the fault. This can be done by pressing the STOP/RESET key on the keypad, cycling the main power, or using an external reset signal wired to the RES terminal. If the fault appears again immediately, a more serious hardware issue may be present.

Parts Often Needed

Cooling Fan: The fan is a mechanical component with a finite lifespan. When it fails, E.FIN faults are inevitable. These are typically sold as complete, plug-in modules.

Braking Resistor: For applications with frequent or rapid deceleration cycles, an external braking resistor is often necessary to dissipate regenerative energy and prevent E.OVx faults.

FR-DU07 Keypad: Also known as a Parameter Unit (PU), this keypad is essential for diagnostics and programming. It can be damaged in harsh industrial environments.

When to Call a Pro

If you have verified the motor and wiring are good but continue to get overcurrent faults (E.OCx), the drive’s power module (IGBTs) may have failed. This typically requires replacing the entire drive unit.

Faults like E.CPU or E.PE indicate an internal control board or memory failure. If these persist after a power cycle, the drive needs to be repaired or replaced.

If you are not comfortable or qualified to work with high-voltage industrial equipment, always call a qualified technician or systems integrator. VFDs contain large capacitors that can hold a dangerous electrical charge even after power has been disconnected.

Quick FAQ

What is an E.OC1 fault on a Mitsubishi FR-F700?

E.OC1 is an overcurrent fault during acceleration. It means the drive delivered too much current trying to ramp up the motor. The most common cause is the acceleration time (Parameter 7) being set too short. It can also be caused by a short circuit in the motor wiring.

How do I clear an E.OV1 overvoltage fault?

E.OV1, E.OV2, or E.OV3 faults happen when the drive's DC bus voltage gets too high, usually from the motor regenerating power during a fast deceleration. To fix it, increase the deceleration time (Parameter 8) or install an appropriate external braking resistor.

What does the E.THT fault mean?

E.THT is an inverter overload fault. It means the drive was operating above its rated current for too long, causing the electronic thermal protection to trip. You should check for mechanical overload on the motor or reduce the load.

Why does my FR-F700 show an E.LF output phase loss fault?

The E.LF fault indicates that one of the output phases (U, V, or W) to the motor is disconnected. This is almost always caused by a loose wire at the drive's output terminals or in the motor's connection box. Check all motor wiring for continuity.


Need a professional? Compare Industrial repair options before replacing parts.
Compare Repair Options
Share this post on:

Previous Post
Mitsubishi FR-D700 Fault Codes List: OC1, OV3, THT, THM, GF and PE Fixes
Next Post
Mitsubishi FR-A800 E.OC1 Overcurrent Fault