Maytag Washer Leaking Water - Causes & Fix

Maytag Washer Leaking Water — What’s Happening

Maytag does not list “leaking water” as a fault code. It is a general symptom with multiple possible sources depending on where the water appears. The exact cause depends on whether the leak is coming from the front, the bottom, or around the dispenser and door area.

For front-load machines, Maytag points to the door seal (bellow), dispenser, detergent use, loading issues, and leveling as common leak-related causes. For leaks from the bottom, Maytag identifies fill and drain hoses, the water pump, tub seal, drain pipe, and water level switch as possible causes.

Jump to Fix

Most Likely Causes

• Loose, kinked, blocked, or damaged fill or drain hoses Hose connections can work loose over time, or the hose itself can crack, kink, or develop pinholes that leak during fill or drain cycles.
• Water pump failure or housing damage A cracked pump body or failed seal at the pump causes water to pool under the washer, especially visible during the drain cycle.
• Dirty, torn, or obstructed door seal or bellow on front-load models Lint, hair, debris, or trapped items in the bellow prevent a proper seal, allowing water to leak from the door during wash or spin.
• Clogged dispenser drawer or cavity with detergent buildup Detergent residue blocks the dispenser flow path and causes water to overflow or leak from the drawer area during fill.
• Faulty tub seal or center tub seal A worn or damaged tub seal allows water to escape from the tub area during fill, agitation, or spin, usually appearing underneath the machine.
• Inlet valve leak or drip when machine is off A failing inlet valve can drip through its body or seat even when the washer is unplugged, leaving water pooled inside or underneath.
• Excess suds from non-HE detergent or overdosing Using too much detergent or non-HE soap creates excessive suds that overflow from the tub or door seal and cause leaking and draining problems.

How to Diagnose and Fix

1. Unplug the washer and shut off the water supply before inspecting any components.
2. Identify where the leak appears (front, bottom, or dispenser area) to narrow down the component family to inspect.
3. Check all fill and drain hoses for cracks, pinholes, kinks, clogs, and loose clamps or fittings, then tighten loose connections or replace damaged hoses.
4. Remove or tilt the washer as needed and watch the pump area during a drain cycle for active dripping from the pump body or water pooling beneath it, then replace the drain pump if the housing is leaking.
5. For front-load models, clean the door bellow and glass, remove lint, hair, debris, and any items trapped in the seal, and replace the bellow if torn, deformed, or not sealing properly.
6. Remove and clean the dispenser drawer and cavity, clear all detergent buildup and blockages, and replace the dispenser assembly if cracked or damaged.
7. Inspect the tub seal if the leak appears during fill, agitation, or from underneath and hoses and pump are not the source, then replace the seal if damaged.
8. Verify the machine is level and loads are balanced after repair, then run a test cycle to confirm no further leaks.

Parts You Might Need

Related Maytag Error Codes

Seeing a code on the display? These match this problem:

• Maytag Washer D1 error code
• Maytag Washer D13 error code
• Maytag Washer D16 error code
• Maytag Washer D3 error code
• Maytag Washer D4 error code
• Maytag Washer D5 error code
• Maytag Washer D7 error code
• Maytag Washer D8 error code
• Maytag Washer D9 error code
• Maytag Washer Drn error code
• Maytag Washer F07 error code
• Maytag Washer F11 error code

When to Call a Pro

Call a professional if the leak persists after checking hoses, pump, and door seal, or if you need to disassemble the tub to reach the tub seal or internal components. A technician has the tools and experience to safely tilt or disassemble the washer, test the water level switch, and replace seals or valves that require cabinet removal or special alignment.