What does Maytag Range LOC Error Code - Causes & Fix mean?

LOC means control lock is active, not a failure. Unlock by holding START/ENTER for 5 seconds or reset power at the breaker for 1 minute.

How do I fix Maytag Range LOC Error Code - Causes & Fix?

Follow the step-by-step diagnosis below. The most likely fix is identified by checking power, sensor resistance, and control-board signals in order — using a multimeter and the part numbers documented in the parts reference table.

Can I keep running the equipment with this fault active?

Generally no. Faults on Appliance units are emitted when a sensor, safety, or control circuit is outside its operating envelope. Running through an active fault risks compressor, heater, or control-board damage. Diagnose and clear the fault first.

What part is most commonly replaced for Maytag Range LOC Error Code - Causes & Fix?

The most frequently replaced parts for Maytag Range LOC Error Code - Causes & Fix are listed in the Parts Reference section of this guide with OEM part numbers and typical price ranges. Check the table for direct replacements.

Is Maytag Range LOC Error Code - Causes & Fix a DIY repair or do I need a technician?

Sensor swaps, fan motor replacements, and condenser cleaning are typical DIY-level repairs. Anything involving refrigerant, gas, or high-voltage (>240V) work requires a licensed technician for both safety and code-compliance reasons.

Maytag Range LOC Error Code - Causes & Fix

Maytag Range LOC Error Code — What It Means

LOC on a Maytag range indicates that the control lock feature is engaged. This is not a fault code pointing to a broken sensor, relay, or control board. When active, the control lock disables the keypad and prevents unintended operation. On some models it also locks the oven door. The display shows LOC whenever a user presses any button while the lock is engaged or if the feature was deliberately turned on. Maytag designs this as a safety feature to prevent accidental changes to cook settings or activation by children.

Jump to Fix

Common Causes

Accidental key hold The user held the START/ENTER key or a dedicated Control Lock button long enough to engage the lockout feature.
Button press during lockout Someone pressed a command pad while the control was already locked, causing LOC to display again.
Persistent lock after power loss A power interruption left the control panel in a locked state that requires a power reset to clear.
Keypad or control panel glitch A rare firmware or interface error causes the lock to remain active even after the correct unlock sequence.

Step-by-Step Fix

Verify the oven and timer are off. Maytag states the lock cannot be engaged while the oven is in use, so confirm all cooking functions are stopped before attempting unlock.
Hold START/ENTER for 5 seconds. On most Maytag ranges this is the standard unlock sequence. Watch the display until LOC disappears and normal operation resumes.
Try the model-specific unlock key if START/ENTER does not work. Some ranges use a dedicated Control Lock button or a different key combination. Check your owner’s manual for the exact procedure.
Perform a power reset if the keypad remains unresponsive. Turn off both circuit breakers (or unplug if accessible) for a full 1 minute, then restore power.
Test keypad response after power is restored. Press a few buttons to confirm the display no longer shows LOC and that commands register normally.
Inspect control panel wiring if the lock persists after reset. Verify that the ribbon cable connecting the keypad overlay to the main control board is seated correctly and shows no damage.
Consult the service manual for your specific model number if the lock will not clear. Persistent symptoms after the correct unlock procedure and a power cycle point to a model-specific control issue rather than a standard LOC event.

Parts Often Needed

Part	Notes
User Interface Control Panel / Keypad Overlay	Amazon \| Required only if the touchpad fails to respond after proper unlock sequence and power reset, indicating a failed membrane or wiring issue.
Main Control Board (ERC / Clock Timer Board)	Amazon \| Needed if the board does not recognize the unlock command and a known-good keypad has been tested, pointing to a board-level fault.

When to Call a Pro

Call a technician if LOC remains displayed after you have tried the correct unlock sequence for your model and completed a full 1-minute power reset at the breaker. A pro will verify the keypad overlay wiring, test the control board’s response to unlock commands, and reference the service literature for your exact model number. Because LOC is a feature rather than a component failure, a persistent lock usually indicates a control panel or board issue that requires diagnostic tools and OEM service documentation to isolate.