What does Maytag Dryer F28 Error Code - Causes & Fix mean?

F28 on a Maytag dryer requires a power reset. Turn off the breaker for 5 minutes, restore power, and run a test cycle to clear the code.

How do I fix Maytag Dryer F28 Error Code - Causes & Fix?

Follow the step-by-step diagnosis below. The most likely fix is identified by checking power, sensor resistance, and control-board signals in order — using a multimeter and the part numbers documented in the parts reference table.

Can I keep running the equipment with F28 active?

Generally no. Faults on Appliance units are emitted when a sensor, safety, or control circuit is outside its operating envelope. Running through an active fault risks compressor, heater, or control-board damage. Diagnose and clear the fault first.

What part is most commonly replaced for Maytag Dryer F28 Error Code - Causes & Fix?

The most frequently replaced parts for Maytag Dryer F28 Error Code - Causes & Fix are listed in the Parts Reference section of this guide with OEM part numbers and typical price ranges. Check the table for direct replacements.

Is Maytag Dryer F28 Error Code - Causes & Fix a DIY repair or do I need a technician?

Sensor swaps, fan motor replacements, and condenser cleaning are typical DIY-level repairs. Anything involving refrigerant, gas, or high-voltage (>240V) work requires a licensed technician for both safety and code-compliance reasons.

Maytag Dryer F28 Error Code - Causes & Fix

Maytag Dryer F28 Error Code — What It Means

The F28 error code on a Maytag dryer does not have a published fault definition in Maytag’s official product help documentation. The manufacturer’s guidance instructs you to perform a power reset by shutting off the circuit breaker for five minutes, restoring power, and then running a timed dry cycle for one minute to see if the code clears. If the code returns after the reset, the issue requires model-specific diagnostics using the technical service sheet or service manual, because Maytag does not publish detailed troubleshooting steps for F28 in public-facing support materials.

Jump to Fix

Common Causes

Temporary control board glitch A transient electronic fault in the main control board can trigger F28 and often clears with a full power reset.
Moisture sensor failure Some third-party sources suggest F28 may relate to a faulty moisture sensor, though this is not confirmed in Maytag’s official documentation.
Wiring harness issue A loose or corroded connection in the moisture sensor wiring harness can send incorrect signals to the control board.
Faulty user interface control The user interface board may fail to communicate properly with the main control, causing error codes to appear.
Thermistor or drive motor fault In some cases, a defective thermistor or drive motor can trigger non-specific error codes on certain Maytag dryer models.

Step-by-Step Fix

Turn off power at the circuit breaker and wait a full five minutes to allow the control board to fully reset.
Restore power by switching the breaker back on and wait for the control panel to light up.
Select a timed dry cycle on the control panel and start the dryer.
Monitor the cycle for one minute to verify whether the F28 code reappears on the display.
If the code clears, run a full test load to confirm normal operation and that the error does not return.
If F28 returns, locate the technical service sheet (usually taped inside the front panel or console) and follow the model-specific diagnostic flowchart for F28.
Check all wire harness connections to the moisture sensor strips, thermistor, and control boards for looseness or corrosion, and re-seat connectors as needed.

Parts Often Needed

Part	Notes
Moisture sensor strips	Amazon \| Metal sensor bars inside the drum that detect dampness. Match to your model number.
Electronic control board (main)	Amazon \| The primary control module. Verify the board part number from your service sheet before ordering.
User interface control board	Amazon \| The display and button panel. Confirm compatibility with your exact Maytag dryer model.

When to Call a Pro

Call a qualified appliance technician if the F28 code returns after a full power reset or if you are uncomfortable opening the dryer cabinet to access the technical service sheet. Because Maytag does not publish detailed F28 diagnostics for the public, a technician with access to model-specific service manuals and diagnostic software can pinpoint the exact sensor, board, or wiring fault. Professional diagnosis is especially important if you have already replaced common parts without success or if your dryer is still under warranty.