How do I fix Kenmore Refrigerator Door Bin Replacement - Signs & How-To?

Follow the step-by-step diagnosis below. The most likely fix is identified by checking power, sensor resistance, and control-board signals in order — using a multimeter and the part numbers documented in the parts reference table.

Can I keep running the equipment with this fault active?

Generally no. Faults on Appliance units are emitted when a sensor, safety, or control circuit is outside its operating envelope. Running through an active fault risks compressor, heater, or control-board damage. Diagnose and clear the fault first.

What part is most commonly replaced for Kenmore Refrigerator Door Bin Replacement - Signs & How-To?

The most frequently replaced parts for Kenmore Refrigerator Door Bin Replacement - Signs & How-To are listed in the Parts Reference section of this guide with OEM part numbers and typical price ranges. Check the table for direct replacements.

Is Kenmore Refrigerator Door Bin Replacement - Signs & How-To a DIY repair or do I need a technician?

Sensor swaps, fan motor replacements, and condenser cleaning are typical DIY-level repairs. Anything involving refrigerant, gas, or high-voltage (>240V) work requires a licensed technician for both safety and code-compliance reasons.

Kenmore Refrigerator Door Bin Replacement - Signs & How-To

Q: What does Kenmore Refrigerator Door Bin Replacement - Signs & How-To mean?

Cracked, loose, or missing door bins are the most common problem. Replacing the bin with the correct OEM part for your model restores door storage.

Kenmore Refrigerator Door Bin Replacement — What This Part Does

The door shelf bin is a plastic storage bin that clips to the inside of your refrigerator door and holds bottles, gallon containers, and other items. These bins are designed to slide into mounting points on the door liner and lock in place with side tabs.

Bins fail when plastic fatigues from repeated heavy loading, especially gallon milk jugs. The mounting tabs can crack or break, causing the bin to slip out or not lock into position. Incorrect part selection also causes fitment problems because Kenmore bins vary by refrigerator design and the exact model number matters.

Jump to Replacement Steps

Signs It Needs Replacing

Bin is cracked or visibly broken You see cracks in the plastic body or along the mounting tabs where the bin attaches to the door.
Bin slips or falls out of the door The bin does not stay locked in position and comes loose when you open the door or load items.
Mounting tabs are missing or deformed The side tabs that lock the bin into the door liner are broken off or bent, preventing proper engagement.
Bin does not align with door slots The bin does not slide into the mounting points smoothly, indicating a wrong part number or damaged door liner.
Door closes poorly or hits the bin A misaligned or broken bin protrudes into the cabinet and prevents the door from closing completely.
Bin is missing entirely The bin was removed or lost and you need to restore door storage capacity.

How to Replace It

Unplug the refrigerator from the wall outlet to make sure safe working conditions.
Locate the model and serial number on the data plate, usually inside the fresh-food compartment along the side wall or on the ceiling, and write down the full model number for parts lookup.
Cross-check the replacement bin part number against your exact Kenmore model number using the manufacturer’s parts catalog or an OEM parts supplier to confirm compatibility.
Open the refrigerator door and remove any items stored in the damaged bin.
Inspect the bin and the door mounting points for cracks, broken tabs, or deformation to confirm the bin is the problem and the door liner is undamaged.
Lift or push the old bin upward to clear the side locking tabs from the door liner slots, then pull the bin straight out toward you.
Slide the new replacement bin into the door liner mounting slots, aligning the side tabs with the slots on each side of the door.
Push the bin down firmly until you hear or feel the locking tabs engage and the bin is seated flush against the door liner.
Plug the refrigerator back in, close the door, and check that the bin is secure and does not interfere with door closure or operation.

The Part You Need

Part	Notes
Kenmore refrigerator door bin (OEM replacement)	Amazon \| Part numbers vary by model. Common OEM replacements include Frigidaire 240323001 (supersedes 240323007, 890954, AH429724, EA429724, PS429724), Whirlpool WPW10710203 (supersedes W10451871, W10710203, W10463668), and LG AAP73351301 for LG-built Kenmore units. Use your full model number from the data plate to find the exact bin for your refrigerator on the Kenmore parts site or an OEM supplier.

Part

Notes

Kenmore refrigerator door bin (OEM replacement)

Amazon | Part numbers vary by model. Common OEM replacements include Frigidaire 240323001 (supersedes 240323007, 890954, AH429724, EA429724, PS429724), Whirlpool WPW10710203 (supersedes W10451871, W10710203, W10463668), and LG AAP73351301 for LG-built Kenmore units. Use your full model number from the data plate to find the exact bin for your refrigerator on the Kenmore parts site or an OEM supplier.

If this part is failing you may also see one of these codes:

When to Call a Pro

This is a straightforward DIY replacement that requires no tools and no electrical or refrigerant work. Call a pro if the door liner itself is cracked or the mounting slots are damaged, or if you cannot identify the correct replacement part for your model number. A technician can inspect the door liner and order the right bin using the manufacturer’s supersession data.