Skip to content
Industrial Error Code Fixes
Go back

Goodman Furnace Error Codes — All Flash Codes Explained

⚡ Quick Answer

Use this Goodman Furnace Error Codes - All Flash Codes Explained reference to match the code with likely causes, service checks, and repair decisions.

⚡ AT A GLANCEScroll down for full repair guide
What it meansGoodman furnace LED flash codes report ignition lockout, pressure switch stuck open or closed, open high limit, flame without call, reversed polarity, unexpected gas valve energizing, low flame signal, igniter circuit faults, plus E1 communication and EE2 EEPROM faults.
Most likely causeDirty flame sensor rods cause 1-flash lockouts, cracked pressure switch hoses and blocked drain traps cause 2 flashes, clogged air filters cause 4 flashes, swapped hot and neutral cause 6 flashes, and open igniters cause 9 flashes.
First checkCount the flashes through the blower compartment window, clean the flame sensor rod with 400-grit sandpaper, inspect the pressure switch hose and condensate trap, replace the filter, verify polarity at the disconnect, and check igniter continuity.
⏱Repair time15-45 minutes for sensor, filter, hose, and polarity fixes; gas valve and board faults need a technician
🔧Part neededFlame sensor rod, hot-surface igniter, pressure switch, draft inducer motor, control board

Parts to price first

Check the part before you book service.

Flame sensor rod

Part: Goodman 0130F00010

Replace when an 8-flash low flame signal stays under about 1.5 microamps after cleaning, or the rod is cracked.

Hot-surface igniter

Part: Goodman 0130F00008

The fix for a 9-flash igniter circuit fault when the igniter reads open on a continuity test.

Pressure switch

Part: Goodman 0130F00045

For 2-flash or 3-flash codes when the hose and drain trap are clear but the switch will not close or sticks closed.

Draft inducer motor

Part: Goodman 0131M00002P

Replace when the inducer is noisy, slow, or cannot pull enough draft to close a good pressure switch.

$120-$220Check price

Integrated control board

Part: Goodman PCBBF112S / PCBBF123S

Required for an EE2 EEPROM fault or a 7-flash gas valve code once the valve wiring tests good.

$90-$180Check price

Replacement HVAC air filter (exact size)

Restricted airflow trips high-limit, low-airflow, and frozen-coil faults. Filter King cuts custom sizes if the standard size is out of stock.

Furnace and AC filters in bulk (DiscountFilterStore)

Stock a year of filters so the airflow fault does not come back after the fix.

Nordic Pure MERV 8-13 pleated filters (American-made)

Standard and odd sizes in MERV 8, 11, and 13. Match the MERV your blower is rated for; a filter that is too restrictive trips the same airflow faults as a dirty one.

Furnace parts and sequencers (Mobile Home Parts Store)

Limit switches, sequencers, blower motors, and control boards for Nordyne, Intertherm, Miller, and Coleman furnaces.

Gas furnaces, control boards, and blower parts (HVACDirect)

Wholesale-priced OEM-equivalent parts and full systems shipped direct. Compare before paying contractor markup on a replacement.

Repair intent

Need this fixed instead of diagnosed?

Use this Goodman Furnace Error Codes - All Flash Codes Explained reference to match the code with likely causes, service checks, and repair decisions.

Goodman Furnace Error Codes — Quick Reference

Goodman furnaces signal faults through a flashing LED on the control board. Remove the lower access panel and count the repeating blink sequence. One long flash followed by shorter flashes indicates a two-digit code on newer boards; older boards use a simple count. Goodman shares its control board platform with Amana — the codes are identical across both brands.

CodeMeaningQuick Fix
1 flashLockout — retries exceededManual reset; check igniter and gas
2 flashesPressure switch stuck openCheck inducer, hose, drain trap
3 flashesPressure switch stuck closedInspect pressure switch hose routing
4 flashesOpen high-limit deviceReplace filter; check airflow
5 flashesFlame sensed with no call for heatGas valve may be leaking
6 flashes115V AC power reversed / bad groundCheck polarity at furnace disconnect
7 flashesGas valve energized without callGas valve or board fault
8 flashesLow flame sensor signalClean flame sensor rod
9 flashesIgniter circuit faultCheck igniter continuity; replace if open
ContinuousNormal operation (no fault)—
Slow flashStandby / waiting for callNormal
E1Communication fault (some models)Check thermostat wiring
EE2EEPROM memory faultReplace control board

Technician Tips

Goodman furnaces use a simple LED flash system on the control board. The diagnostic LED is usually visible through the blower compartment window. Count the flashes between pauses — that’s your error code. One flash = normal operation. Two flashes = pressure switch fault. Three flashes = limit switch. Four flashes = flame sensor. Goodman flame sensors are notorious for carbon buildup — cleaning with emery cloth every 2-3 years prevents most lockout calls. The control board on GMS8 and GMSS9 models is particularly sensitive to voltage fluctuations — if you see multiple different codes, check the transformer output (should be 24VAC ±10%).

Prevention: Install a whole-house surge protector on the furnace circuit to prevent board damage from power spikes.

Need Replacement Parts?

Before ordering, match the furnace part to the model number, electrical rating, and failure symptom. Check current prices on Amazon - prices and availability change frequently.

Most Common Codes

1 Flash: Ignition Lockout

The furnace tried to light multiple times and gave up. Start with the flame sensor — a dirty rod is the #1 cause. Remove the sensor (single screw), rub the metal rod with 400-grit sandpaper or steel wool, and reinstall. If that doesn’t work, check the hot-surface igniter for cracks and verify the gas valve opens when the thermostat calls for heat.

2 Flashes: Pressure Switch Stuck Open

The draft inducer motor ran but the pressure switch didn’t see enough negative pressure to close. Check: (1) the rubber pressure switch hose for cracks, (2) the condensate drain trap for blockage on 90%+ models, (3) the inducer wheel for debris. A plugged secondary heat exchanger on high-efficiency models is also common.

4 Flashes: High Limit Open

The heat exchanger overheated and tripped the limit switch. Overwhelmingly caused by a clogged air filter. Replace the filter and allow the furnace to cool before resetting. If the limit trips again with a clean filter, check for blocked supply or return registers and verify the blower wheel isn’t clogged with debris.

5 Flashes: Flame Sensed — No Call for Heat

The flame sensor is detecting a signal even when the thermostat isn’t calling for heat. This usually means a leaking gas valve (allowing gas to seep and ignite on the hot surface of the heat exchanger) or a shorted flame sensor wire. This is a safety issue — shut off the gas supply and call a technician.

6 Flashes: Reversed Polarity / Bad Ground

Goodman furnaces are polarity-sensitive. The hot and neutral wires at the furnace disconnect or outlet must be wired correctly. Swap the two leads at the disconnect if needed. Also verify the unit has a proper earth ground — a missing ground is a common cause of nuisance lockouts.

8 Flashes: Low Flame Sensor Signal

The burner lit, but the microamp signal from the flame sensor is too low for reliable flame proving. Clean the sensor rod first. If cleaning doesn’t raise the signal above ~1.5 µA, the sensor rod may be cracked or positioned incorrectly in the burner flame.

When to Call a Pro

A 5-flash (flame sensed with no call) or 7-flash (gas valve energized unexpectedly) code indicates a potentially dangerous condition — gas valve failure or control board malfunction. Turn off the gas supply and contact a licensed technician before attempting further operation.

Quick FAQ

What does 1 flash mean on a Goodman furnace?

One flash is an ignition lockout: the furnace tried to light multiple times and gave up. A dirty flame sensor rod is the top cause. Remove the sensor with its single screw, polish the rod with 400-grit sandpaper or steel wool, reinstall, and reset power.

Why does my Goodman furnace flash 2 times?

Two flashes means the pressure switch is stuck open: the draft inducer ran but the switch did not see enough negative pressure to close. Check the rubber pressure switch hose for cracks and the condensate drain trap for blockage on 90%+ models.

What is Goodman furnace code 4 flashes?

Four flashes means the high-limit device opened because the heat exchanger overheated, overwhelmingly from a clogged air filter. Replace the filter and let the furnace cool before resetting. If it trips again with a clean filter, check the blower and airflow.

Is a Goodman 5 flash or 7 flash code dangerous?

Yes. Five flashes means flame is sensed with no call for heat, and seven flashes means the gas valve is energized unexpectedly. Both point to a leaking gas valve or control board malfunction. Turn off the gas supply and call a technician.


Need a professional? Compare HVAC repair options before replacing parts.
Compare Repair Options
Share this post on:

Previous Post
Gardner Denver Compressor Fault Codes — Complete Guide
Next Post
Goodman EE2 Control Board Communication Fault