Tag: parts
All the articles with the tag "parts".
-
Kenmore Dryer Rear Drum Bearing Replacement - Signs & How-To
Squealing, rumbling, or scraping noise from the back of the drum during rotation means the rear drum bearing is worn. Replacing the bearing kit fixes the noise and restores smooth tumbling.
-
GE Dryer Drum Glides Replacement - Signs & How-To
Squealing or scraping noise and rough drum rotation mean worn drum glides. Replacing the drum glide bearings and support pads fixes the noise and restores smooth tumbling.
-
Maytag Dryer Drum Glides Replacement - Signs & How-To
Worn drum glides cause squealing, rubbing, or binding when the dryer runs. Replacing the front glide kit stops the noise and lets the drum spin freely again.
-
Whirlpool Dryer Drum Glides/Slides Replacement - Signs & How-To
Squealing, scraping, or binding drum? Worn drum glides let the drum drag on the bulkhead. Replacing the glides and felt pad restores smooth rotation.
-
Kenmore Dryer Drum Glides/Slides Replacement - Signs & How-To
Scraping, squealing, or rumbling from your Kenmore dryer means worn drum glides. Replacing the front drum glides and felt seal restores smooth rotation.
-
Whirlpool Dryer Main Control Board Replacement - Signs & How-To
F01 or F1E1 error codes, dryer won't start, or relay clicking often mean a failed main control board. Replacing the board fixes these faults.
-
LG Dryer Main Control Board Replacement - Signs & How-To
Control board drives heating, motor, and display functions. Replacing it fixes persistent electrical faults after breaker and power checks pass.
-
GE Dryer Main Control Board Replacement - Signs & How-To
No start, dead controls, dryer won't heat, or erratic cycles signal a bad GE control board. Replacing it restores normal operation.
-
Samsung Dryer Main Control Board Replacement - Signs & How-To
No heat, won't start, or erratic cycling? A failed main control board stops Samsung dryers dead. Replacing it restores normal operation.
-
GE Dryer Thermal Cut-Off Fuse Kit Replacement - Signs & How-To
Dryer tumbles but won't heat after overheating? A blown thermal cut-off fuse is the cause. Replace the fuse kit and fix airflow to restore heat.
-
Kenmore Dryer Thermal Cut-Off Fuse Kit Replacement - Signs & How-To
No heat, dryer won't start, or runs cold after overheating episode? Thermal cut-off fuse kit (fuse + high-limit thermostat) has blown. Replacing both parts restores heat and safety protection.
-
Maytag Dryer Thermal Cut-Off Fuse Kit Replacement
Dryer runs but won't heat, or burner won't ignite? A blown thermal cut-off fuse is the likely cause. Replace the fuse kit and clear airflow blockages to restore heat.
-
Samsung Dryer Drive Motor Replacement - Signs & How-To
Dryer won't spin, hums but drum stays still, or powers on without starting? A failed drive motor stops the drum and blower. Replacing it restores normal drying.
-
GE Dryer Drive Motor Replacement - Signs & How-To
A failed GE dryer motor causes no start, humming, or no drum spin. Replacing the drive motor restores proper drum and blower operation.
-
Maytag Dryer Drive Motor Replacement - Signs & How-To
F26 error code, dryer won't start, or humming without drum spin mean drive motor failure. Replacing the motor restores normal operation.
-
Kenmore Dryer Drive Motor Replacement - Signs & How-To
No drum spin, humming motor, or F26 error mean your drive motor failed. Replacing the motor and checking the blower wheel restores normal drying.
-
Maytag Dryer Flame Sensor Replacement - Signs & How-To
Dryer runs but won't heat or heats inconsistently when the flame sensor fails to control the igniter and gas valve sequence. Replacing the sensor restores normal burner operation.
-
Whirlpool Dryer Drive Motor Replacement - Signs & How-To
Motor won't start, F-26 error, or dryer hums but won't spin? A failed drive motor is the fix. Replace the motor to restore drum rotation.
-
Kenmore Dryer Flame Sensor Replacement - Signs & How-To
Burner lights then shuts off, won't ignite, or cycles erratically. Replacing the failed flame sensor restores proper gas-burner operation.
-
GE Gas Dryer Flame Sensor Replacement - Signs & How-To
No heat, igniter glows but won't light, or intermittent heat means your GE dryer flame sensor is failing. Replacing it restores normal burner operation.
-
Whirlpool Dryer Flame Sensor Replacement - Signs & How-To
A failed flame sensor stops your Whirlpool gas dryer from heating. Replace the radiant flame sensor (WP338906) to restore burner ignition.
-
GE Gas Dryer Valve Solenoid Replacement - Signs & How-To
Gas dryer tumbles but won't heat or heats intermittently when solenoid coils fail. Replacing the valve coils restores ignition and heat.
-
Maytag Dryer Gas Valve Coils Replacement - Signs & How-To
Igniter glows but no flame appears, or dryer heats only at startup then quits. Replacing the gas valve solenoid coil kit restores burner ignition.
-
Kenmore Gas Dryer Valve Coil Kit Replacement - Signs & How-To
Dryer heats once then stops, or no heat at all? Failed gas valve coils prevent the valve from opening. Replacing the coil kit restores heat.