Tag: maytag
All the articles with the tag "maytag".
-
Maytag Washer F11 Error Code - Causes & Fix
F11 means a motor control communication fault. Most often the machine control board or motor control unit has failed and needs replacement.
-
Maytag F07 Error Code - Causes & Fix
F07 on Maytag top-load washers means laundry detected during Clean Washer cycle. Remove all items from tub, clear code, and restart cycle.
-
Maytag Washer d13 Error Code - Causes & Fix
d13 is not a standard Maytag code. It's likely a misread of dL, SD, F3 E1, or F9 E1. Verify the exact display, reset, then check drain and suds.
-
Maytag Washer d9 Error Code - Causes & Fix
d9 on a Maytag washer means low voltage detected at the control. Most often fixed by checking the outlet, power cord, and internal connections.
-
Maytag Washer d8 Error Code - Causes & Fix
d8 means slow drain detected on legacy Maytag top-loaders. Most often caused by a kinked drain hose or clogged pump. Clear path and test.
-
Maytag d7 Error Code - Causes & Fix
d7 means slow fill detected. Check both supply valves are fully open, clean inlet screens, and inspect hoses for kinks or restrictions.
-
Maytag Washer D5 Error Code - Causes & Fix
D5 (or Sd/5d) on most Maytag washers means excess suds detected. Most common fix: let the washer run its suds routine and switch to HE detergent.
-
Maytag Washer D3 Error Code - Causes & Fix
D3 is not a standard Maytag code. Most likely you're seeing F3 E1, a water-level pressure sensor fault. Check the pressure hose first.
-
Maytag Washer D1 Error Code - Causes & Fix
D1 means water level circuit failure on the control board. Most common fix: replace the main control board after checking wiring.
-
Maytag Washer F9E1 Error Code - Causes & Fix
F9E1 means your Maytag took too long to drain. The usual fix is clearing the drain pump filter and hose, or replacing a failed drain pump.
-
Maytag Washer LD Error Code - Causes & Fix
LD means long drain, the washer is draining too slowly. The usual fix is clearing the drain filter and hose, or replacing a failed drain pump.
-
Maytag Washer LF Error Code - Causes & Fix
LF means long fill, the washer is filling too slowly or not at all. The usual fix is clearing the inlet screens or replacing the water inlet valve.
-
Maytag Washer F5E1 Error Code - Causes & Fix
F5E1 means the washer reads the lid as locked but the lid switch is open. The usual fix is replacing the lid switch or lock assembly.
-
Maytag Washer F5E2 Error Code - Causes & Fix
F5E2 means the washer cannot lock the lid or door before a cycle. The usual fix is clearing the latch area or replacing the door lock assembly.
-
Maytag Washer F5E3 Error Code - Causes & Fix
F5E3 means the washer cannot confirm the lid or door is locked. The usual fix is clearing the latch or replacing the door lock assembly.
-
Maytag Washer F7E1 Error Code - Causes & Fix
F7E1 means the washer cannot reach the right drum speed. On top-load models the usual fix is replacing the shift actuator.
-
Maytag Washer F7E5 Error Code - Causes & Fix
F7E5 means the control cannot tell the position of the shifter. On top-load Maytag washers the usual fix is replacing the shift actuator.
-
Maytag Washer F8E1 Error Code - Causes & Fix
F8E1 means your Maytag is filling too slowly or not at all. The usual fix is clearing a clogged inlet screen or replacing the water inlet valve.
-
Maytag Washer F8E2 Error Code - Causes & Fix
F8E2 is a dispenser system fault on front-load Maytag washers. The usual fix is cleaning the dispenser or replacing the dispenser motor.
-
Maytag F21 Error Code - Causes & Fix
F21 means your Maytag washer detected a long drain or no-drain condition. The most common fix is cleaning the drain pump filter/coin trap.
-
Maytag F5 E2 Error Code - Causes & Fix
F5 E2 means the door or lid won't lock. Most often the door isn't fully closed or the lock assembly has failed and needs replacement.
-
Maytag Washer Error Codes — Complete Fix Guide (Bravos + Centennial)
Maytag washer error codes for Bravos, Centennial, MVWB, MVWX, and MHW front-load models. Covers F1E1-F9E1, dE, Sud, Lid, dL, ndF and door/drain/balance faults.