Tag: ge

All the articles with the tag "ge".

• GE Oven F96 Error Code - Causes & Fix

  31 May, 2026

  F96 means the control board cannot detect upper oven cooling fan speed. Most often caused by a failed fan motor or hall sensor.

• GE Oven F20 Error Code - Causes & Fix

  31 May, 2026

  F20 means oven temperature exceeded safe limits. Most often caused by a failed oven temperature sensor or stuck relay on the control board.

• GE Oven F6 Error Code - Causes & Fix

  31 May, 2026

  F6 means a keypanel fault. GE says the touchpad often needs replacement. Check connectors first, then swap the keypanel assembly.

• GE Dishwasher F56 Error Code - Causes & Fix

  31 May, 2026

  F56 means your GE dishwasher did not drain. Check for a kinked drain hose, clogged air gap, or blocked disposer connection first.

• GE Refrigerator tF Code - Causes & Fix

  31 May, 2026

  The tF code on a GE refrigerator is not an error. It means TurboFreeze mode is active. Hold the Freezer button for 3 seconds to turn it off.

• GE Refrigerator tC Error Code - Causes & Fix

  31 May, 2026

  tC on a GE refrigerator means TurboCool mode is active, not a fault. Press and hold the Fridge pad for 3 seconds to turn it off.

• GE Dishwasher EF Error Code - Causes & Fix

  30 May, 2026

  EF is not a verified GE code. The closest GE fault is C3 (won't drain). Reset power, check float, clear sump debris, and inspect drain hose.

• GE Dishwasher PrS Error Code - Causes & Fix

  30 May, 2026

  PrS means the pressure sensor is sending an invalid signal. Most often caused by a failed sensor or loose wiring harness connection.

• GE Dishwasher FFF Error Code - Causes & Fix

  30 May, 2026

  FFF is not a standard GE code. GE drain faults show as C1 or C3. Clean the filter and drain hose first, then check the pressure sensor.

• GE Dishwasher PF Error Code - Causes & Fix

  30 May, 2026

  PF means power failure detected. Most often caused by a tripped breaker or brief outage. Clear by pressing Start/Cancel.

• GE Dishwasher C1 Error Code - Causes & Fix

  30 May, 2026

  C1 means the drain was partly blocked and pump out ran too long. Most often a clogged filter, air gap, or kinked drain hose.

• GE Dishwasher C3 Error Code - Causes & Fix

  30 May, 2026

  C3 means the dishwasher will not drain and water stays in the tub. Most often a clogged filter or a drain pump jammed by debris or glass.

• GE Dishwasher C4 Error Code - Causes & Fix

  30 May, 2026

  C4 means an overfill was sensed after a power failure. Most often a stuck float switch, or a water inlet valve that will not close.

• GE Dishwasher C5 Error Code - Causes & Fix

  30 May, 2026

  C5 means the dishwasher underfilled or pumped out too fast. Most often a low water supply or a clogged water inlet valve.

• GE Dishwasher C6 Error Code - Causes & Fix

  30 May, 2026

  C6 means the wash water never reached the target temperature. Most often a cool incoming supply or a failed dishwasher heating element.

• GE Dishwasher C7 Error Code - Causes & Fix

  30 May, 2026

  C7 means the water temperature sensor circuit failed open or shorted. Most often a bad thermistor or a loose sensor wiring connection.

• GE Dishwasher C8 Error Code - Causes & Fix

  30 May, 2026

  C8 means the detergent cup cannot open fully during the cycle. Most often debris around the cup or a failed dispenser actuator.

• GE Dishwasher FTD Error Code - Causes & Fix

  30 May, 2026

  FTD means the dishwasher failed to drain on time. Most often a gunked up filter or a drain pump jammed by food debris or glass.

• GE Oven F0 Error Code - Causes & Fix

  30 May, 2026

  GE oven F0 means a stuck key or shorted touch panel. Most fixes start by reseating the ribbon cable, then replacing the control panel.

• GE Oven F1 Error Code - Causes & Fix

  30 May, 2026

  GE oven F1 is a control relay fault that locks out the range as a safety step. The usual fix is replacing the electronic oven control board.

• GE Oven F4 Error Code - Causes & Fix

  30 May, 2026

  GE oven F4 means the temperature sensor reads shorted, under about 950 ohms. The common fix is replacing the RTD oven temperature sensor.

• GE Oven F5 Error Code - Causes & Fix

  30 May, 2026

  GE oven F5 points to a fault in the electronic oven control supervisory or relay circuit. The fix is usually replacing the control board.

• GE Oven F9 Error Code - Causes & Fix

  30 May, 2026

  GE oven F9 means a door lock fault, often during self clean. The common fix is replacing the door lock motor and switch assembly.

• GE Oven FC Error Code - Causes & Fix

  30 May, 2026

  GE oven FC is a door lock circuit fault, often during self clean. The usual fix is freeing the latch or replacing the door lock motor assembly.