Tag: appliance

All the articles with the tag "appliance".

• LG Dryer E1 Error Code - Causes & Fix

  7 Jun, 2026

  E1 (tE1) means a thermistor fault. Most often a failed temperature sensor or loose connector. Reset power first, then check sensor.

• LG Dryer E00 Error Code - Causes & Fix

  7 Jun, 2026

  E00 means the display PCB cannot read software from the main control board. Unplug for 60 seconds and restart-if it returns, a board is faulty.

• LG Dryer D95 Error Code - Causes & Fix

  7 Jun, 2026

  D95 means 95% airflow blockage in the exhaust duct. Clean the lint filter and check the outside vent for obstructions or clogs.

• LG Dryer D90 Error Code - Causes & Fix

  7 Jun, 2026

  D90 means 90% duct blockage. Clean the lint filter, check the exterior vent hood for clogs, and inspect the flex hose for kinks.

• LG Dryer D80 Error Code - Causes & Fix

  7 Jun, 2026

  D80 means about 80% airflow restriction in the exhaust vent. Clean the entire vent run from lint screen to exterior hood first.

• LG Dryer D75 Error Code - Causes & Fix

  7 Jun, 2026

  D75 means 75% exhaust blockage. Clean lint from the entire vent run, check for crushed ducts, and verify air blows outside.

• LG Dryer Add Error Code - Causes & Fix

  7 Jun, 2026

  Add means add water to the steam feeder. Fill the drawer to the MAX line with tap water and close it fully. Problem solved in 1 minute.

• LG Dishwasher tE Error Code - Causes & Fix

  7 Jun, 2026

  tE means the control board detected a faulty temperature sensor signal. Most often a failed thermistor is to blame. Replace the sensor.

• LG Dishwasher PE Error Code - Causes & Fix

  7 Jun, 2026

  PE on an LG dishwasher means a water level sensor fault. The most common fix is replacing the defective sensor or repairing its wiring.

• Samsung HR Error Code - Causes & Fix

  7 Jun, 2026

  HR means heater error on Samsung washers. Most often caused by reversed hot/cold hoses. Swap hoses so hot supply connects to hot inlet.

• Samsung bE0 Error Code - Causes & Fix

  7 Jun, 2026

  Samsung bE0 means a control-panel button is stuck or continuously pressed. Free stuck buttons and clean moisture from the keypad first.

• LG Dishwasher OE Error Code - Causes & Fix

  7 Jun, 2026

  OE means drainage failure. Water remains in the tub. Most often: clogged filter or kinked drain hose. Clean filters and check the hose.

• LG Dishwasher nE Error Code - Causes & Fix

  7 Jun, 2026

  nE means vario motor error (spray function fault). Most often a failed vario motor. Check wiring and test motor resistance first.

• LG Dishwasher LE Error Code - Causes & Fix

  7 Jun, 2026

  LE means motor error on LG dishwashers. Most often caused by a failed wash motor or debris blocking the pump. Reset power first.

• LG Dishwasher E1 Error Code - Causes & Fix

  7 Jun, 2026

  E1 means a leak or overfill triggered the float switch. Most often water pooled in the base pan from a door seal or internal leak.

• LG Dishwasher CR Error Code - Causes & Fix

  7 Jun, 2026

  CR means your LG dishwasher is stuck in Test Mode (Continuous Run). Turn the unit off at the breaker for 30 seconds, then power back on.

• LG Dishwasher CE Error Code - Causes & Fix

  7 Jun, 2026

  CE is a motor error on LG dishwashers. The wash motor or its wiring harness has failed. Reset power, check connections, replace motor if needed.

• LG Dishwasher bE Error Code - Causes & Fix

  7 Jun, 2026

  bE means bubble error: too many suds. Fix: confirm you're using dishwasher detergent (not dish soap), run empty cycle to clear foam.

• LG Dishwasher AE Error Code - Causes & Fix

  7 Jun, 2026

  AE means water in the base pan triggered the leak sensor. Most often caused by a dirty door gasket. Dry the pan and find the leak source.

• Samsung Washer UC Error Code - Causes & Fix

  7 Jun, 2026

  UC means power supply or voltage problem. Most often caused by unstable line voltage or using an extension cord. Plug directly into a dedicated circuit.

• Samsung Washer UB Error Code - Causes & Fix

  7 Jun, 2026

  UB means unbalanced load. The drum is weighted to one side during spin. Pause, untangle and redistribute laundry, then restart.

• Samsung Washer tE2 Error - Causes & Fix

  7 Jun, 2026

  tE2 means a temperature sensor circuit fault. Most often a bad thermistor or loose connector. Check wiring and sensor resistance first.

• Samsung tE1 Error Code - Causes & Fix

  7 Jun, 2026

  tE1 on Samsung washers means a temperature-sensor fault. Most often a bad sensor or loose connector. Check the thermistor first.

• Samsung Washer tE Error Code - Causes & Fix

  7 Jun, 2026

  tE means temperature sensor fault. Most often a failed thermistor or loose connector. Check sensor resistance and wiring first.