Tag: appliance

All the articles with the tag "appliance".

• GE Washer Main Control Board Replacement - Signs & How-To

  1 Jun, 2026

  No power, no lights, dead console, or washer won't start despite good AC power usually means a failed main control PCB. Replacing the board and programming it (if needed) restores operation.

• Samsung Washer Main Control Board Replacement - Signs & How-To

  1 Jun, 2026

  Dead display, unresponsive buttons, dC error, no cycle start, or random pauses mean your main control board has failed. Replacing it restores operation.

• Whirlpool Washer Shock Absorber / Suspension Rod Kit Replacement

  1 Jun, 2026

  Worn suspension rods cause tub bounce, loud banging, and off-balance shaking. Replacing the rod kit with matching balls and bushings stops the vibration and recenters the tub.

• Samsung Washer Suspension Rod Replacement - Signs & How-To

  1 Jun, 2026

  Banging, excessive vibration, tub sag, or no spin? Worn suspension rods let the tub move freely. Replacing the rod kit stops the noise and restores spin.

• Whirlpool Washer Tub Bearing Replacement - Signs & How-To

  1 Jun, 2026

  Loud roaring during spin, basket wobble, and water leaks signal worn tub bearings. Replacing the bearings and seal restores smooth rotation.

• Samsung Washer Tub Bearing Replacement - Signs & How-To

  1 Jun, 2026

  Grinding noise, water leaks at rear, and drum wobble signal failed tub bearings. Replacing the bearing kit and seal restores smooth spin.

• LG Washer Tub Bearing Replacement - Signs & How-To

  1 Jun, 2026

  Grinding noise, excessive basket play, LE or UE codes, and hard drum rotation point to a bad tub bearing. Replacing the rear tub bearing and seal restores quiet spin cycles.

• GE Washer Lid Switch Replacement - Signs & How-To

  1 Jun, 2026

  When your GE top-load washer won't agitate or spin but still fills and drains, the lid switch has likely failed. Replacing it restores the safety interlock and normal operation.

• Kenmore Washer Lid Switch Replacement - Signs & How-To

  1 Jun, 2026

  Kenmore lid switch failure stops spin and drain when the washer thinks the lid is open. Replace the switch to restore normal wash cycles.

• Maytag Washer Lid Switch Replacement - Signs & How-To

  1 Jun, 2026

  Washer won't start, agitate, or spin when lid is closed. Replacing the failed lid switch or lid lock assembly restores normal operation.

• Whirlpool Washer Lid Switch Replacement - Signs & How-To

  1 Jun, 2026

  If your Whirlpool washer agitates but won't spin, or stops mid-cycle when the lid is closed, a faulty lid switch is likely. Replacing the switch assembly restores the spin cycle.

• Kenmore Washer Drive Belt Replacement - Signs & How-To

  1 Jun, 2026

  A failed drive belt stops the washer from spinning or agitating, often with squealing or burning-rubber smells. Replacing the belt restores power transfer.

• Maytag Washer Drive Belt Replacement - Signs & How-To

  1 Jun, 2026

  Worn, cracked, or broken drive belts cause no spin, no agitate, slow drum movement, or squealing. Replacing the belt restores torque transfer.

• Whirlpool Washer Door Boot Seal Replacement - Signs & How-To

  1 Jun, 2026

  Leaking, torn, or moldy door boot seals cause front-load washers to drip or smell. Replacing the door bellow gasket restores the seal.

• Whirlpool Washer Drive Belt Replacement - Signs & How-To

  1 Jun, 2026

  Broken or worn Whirlpool washer drive belts cause no-spin and poor agitation. Replacing the belt restores wash and spin drum drive.

• LG Washer Door Boot Seal Replacement - Signs & How-To

  1 Jun, 2026

  Torn or moldy door boot seals leak water and smell. Replacing the bellow gasket stops front-load door leaks and restores the water seal.

• Samsung Washer Door Boot Seal Replacement - Signs & How-To

  1 Jun, 2026

  Puddles at the front, visible tears, or mold on the rubber gasket mean the door boot seal has failed. Replacing it stops leaks and restores the water barrier.

• Whirlpool Washer Water Inlet Valve Replacement - Signs & How-To

  1 Jun, 2026

  Whirlpool washers that won't fill, overfill, leak, or keep filling after unplugging need a new water inlet valve. This guide covers diagnosis and replacement.

• Maytag Washer Water Inlet Valve Replacement - Signs & How-To

  1 Jun, 2026

  Washer won't fill, fills slowly, overfills, or continuously fills when the inlet valve fails. Replacing the valve assembly fixes fill and shutoff problems.

• Samsung Washer Water Inlet Valve Replacement - Signs & How-To

  1 Jun, 2026

  No fill, slow fill, leaking, or won't stop filling? Replace the water inlet valve-the solenoid-controlled assembly that opens to let water into your Samsung washer.

• GE Washer Water Inlet Valve Replacement - Signs & How-To

  1 Jun, 2026

  Washer won't fill, fills slowly, or leaks at the valve? Replacing the water inlet valve fixes faulty solenoids, clogged screens, and cracked valve bodies.

• Maytag Washer Door Lock/Latch Assembly Replacement - Signs & How-To

  1 Jun, 2026

  Door won't lock, lid won't latch, or washer won't start because the lock assembly can't confirm a secure close. Replacing the assembly fixes it.

• Whirlpool Washer Door Lock/Latch Assembly Replacement

  1 Jun, 2026

  Washer won't start, shows lock error, or door won't latch. Replacing the failed door lock/latch assembly restores the safety interlock.

• Samsung Washer Door Lock / Latch Assembly Replacement

  1 Jun, 2026

  Door won't lock, washer won't start, or dE/DC error codes mean the door lock assembly has failed. Replacing it restores secure door locking.