Skip to content
Industrial Error Code Fixes
Go back

More industrial fault codes

Servo Motor Fault Codes Guide

⚡ Quick Answer

Master reference for servo motor fault codes, drive alarms, and common troubleshooting patterns across Fanuc, Mitsubishi, Siemens, Yaskawa, Delta, and more.

⚡ AT A GLANCEScroll down for full repair guide
What it meansServo drive and motor alarms fall into five core categories: overcurrent, encoder feedback loss, position deviation, motor overtemperature, and drive communication faults
Most likely causeMechanical axis binding or dry ways, oil-contaminated or broken encoder cables, depleted absolute encoder batteries, coupling slip, or drive cooling fan failure
First checkSeparate mechanical from electrical by testing if the axis moves freely, read both the CNC control alarm and drive amplifier code, and inspect motor and encoder cables for damage or oil ingress
⏱Repair time30 minutes for battery or cooling fan replacement to 3 hours for cable routing or mechanical ballscrew adjustment
🔧Part neededAbsolute servo encoder backup battery, servo drive cooling fan, shielded encoder feedback cable, flexible servo shaft coupling, servo motor power cable

Parts to price first

Check the part before you book service.

Absolute Servo Encoder Backup Battery

Restores absolute position memory when encoder feedback alarms appear after power-down; measure battery terminal voltage before resetting home position.

Servo Drive Amplifier Cooling Fan

Resolves overtemperature faults caused by poor amplifier or motor cooling; verify fan rotation and clear heatsink dust before replacing.

Flexible Jaw Servo Motor Shaft Coupling

Eliminates position deviation alarms caused by coupling slip between the servo motor shaft and ballscrew; match bore diameters and torque rating before ordering.

Shielded Servo Encoder Feedback Cable

Fixes intermittent encoder feedback alarms caused by broken conductors in cable tracks or oil contamination at the connector; inspect connector pins for coolant ingress first.

$45-$120Check price

Shielded Servo Motor Power Cable Assembly

Clears overcurrent faults triggered by phase-to-phase or phase-to-ground shorts in flexing motor leads; insulation-test the cable disconnected from the drive before buying.

$65-$160Check price

Equipment service manual download (eManualOnline)

The full OEM-style workshop manual has the wiring diagram, test values, and the fault table this guide summarizes. Instant PDF download.

Repair intent

Need this fixed instead of diagnosed?

Master reference for servo motor fault codes, drive alarms, and common troubleshooting patterns across Fanuc, Mitsubishi, Siemens, Yaskawa, Delta, and more.

Servo Motor Fault Codes — What They Usually Mean

Servo alarms can be intimidating because the motor, encoder, amplifier, mechanics, and control all interact. In practice, most servo faults fall into five groups: overcurrent, encoder feedback, overtravel/position error, overtemperature, and communication faults.

Jump to Fix

Common Servo Fault Categories

Fault TypeTypical Meaning
OvercurrentAxis jam, cable short, amplifier problem
Encoder feedbackLost position, encoder cable fault, battery issue
Position deviationAxis can’t keep up with commanded motion
OvertemperatureMotor overloaded or cooling poor
CommunicationDrive network or amplifier not ready

Need Replacement Parts?

Before ordering, match the replacement part to the model number, electrical rating, and failure symptom:

Common Causes Across Brands

Step-by-Step Fix

  1. Separate mechanical from electrical — Can the axis move freely by hand or jog slowly?
  2. Read both control alarm and drive amplifier alarm — They rarely tell the full story alone.
  3. Inspect encoder and motor cables — They fail more often than the motor itself.
  4. Check axis load and lubrication — Dry ways and tight ballscrews create servo faults fast.
  5. Back up parameters before drive replacement.

Common Brands

When to Call a Pro

If a servo axis faults repeatedly under low load or loses home position unexpectedly, get a qualified motion technician involved. Persistent servo alarms can damage machine accuracy long before total failure happens.

Quick FAQ

What are the five main categories of servo motor fault codes?

Most servo alarms across Fanuc, Mitsubishi, Siemens, Yaskawa, and Delta drives group into overcurrent, encoder feedback, position deviation, overtemperature, and communication faults.

How do I tell if a servo fault is mechanical or electrical?

Check whether the axis moves freely by hand or during slow jog and inspect way lubrication and ballscrew drag. Reading both the controller alarm and the drive amplifier alarm helps isolate mechanical binding from cable or drive faults.

What usually causes servo encoder feedback alarms?

Encoder alarms are most often caused by oil contamination in the motor connector, broken wires inside flexing encoder cables, or a dead backup battery on absolute encoder systems.

What should I do before replacing a faulted servo drive amplifier?

Always back up all drive parameters before removing the old amplifier, and inspect the motor and encoder cables first since flexing cables fail more often than the motor or drive.


Share this post on:

Previous Post
Yaskawa SGDV SERVOPACK Alarm Codes (A.100, A.400, A.710 Fixes)
Next Post
Fanuc Alarm 400 (SV0400) - Servo Overload Fix Guide