Samsung Range and Oven Error Codes — Complete Guide
Samsung ranges and ovens are known for their reliability, but like all appliances, they can throw error codes. When your oven display shows a code like SE, C-d0, or C-10, it’s the control board telling you exactly what is wrong — if you speak the language.
This guide covers every common Samsung range error code, what it means, how serious it is, and what you can do about it.
Master Quick Reference Table
| Code | Meaning | Severity | Likely Fix |
|---|---|---|---|
| SE | Control lock (or “System Error” on older models) | Low | Unlock touchpad or check ribbon cable |
| C-d0 | PCB communication failure between display and main board | Moderate | Reseat ribbon cables or replace display PCB |
| C-10 | Oven temperature sensor open circuit | Moderate | Test and replace oven thermistor |
| F-22 | Calibration data corrupted or control board failure | Moderate to High | Reset, recalibrate, or replace control board |
| bE | Bad touchpad / key stuck | Low | Clean touchpad or replace keypad |
| E1–E4 | Various sensor or relay faults (model-specific) | Varies | Consult manual for your exact model |
| 5E | Short circuit detected | High | Requires professional diagnosis |
SE Error Code
SE on a Samsung range stands for control lock — the touchpad has been locked and is unresponsive to normal presses. On some older models, SE means “System Error.”
How to fix it:
- Try unlocking: press and hold Bake + Broil + 0 for 3 seconds.
- If that doesn’t work, hold Bake + Broil + Timer for 3 seconds.
- Power cycle the range at the breaker for 5 minutes.
- If SE persists, the ribbon cable between the touchpad and control board may be loose or damaged.
- Last resort: replace the touchpad assembly.
For a deeper dive, see our dedicated Samsung Range SE Error Code guide.
C-d0 Error Code
C-d0 (sometimes shown as C-d0 on the display) means the display board cannot communicate with the main power control board. This usually comes down to a loose ribbon cable, a dead display board, or a dead main board.
How to fix it:
- Power cycle the range at the breaker (wait 5 minutes).
- Open the back panel and reseat all ribbon cables on the control board.
- Check the display board for visible damage (burnt spots, bulging capacitors).
- Replace the display PCB or main control PCB depending on diagnosis.
See our Samsung Range SE and C-d0 Error Code guide for detailed steps.
C-10 Error Code
C-10 indicates the oven temperature sensor (thermistor) has an open circuit — the control board can’t read the oven temperature. Without a temperature reading, the oven will not heat.
How to fix it:
- Test the oven sensor with a multimeter. It should read roughly 1080 ohms at room temperature.
- If the reading is OL (open loop) or 0, replace the sensor.
- If the reading is in range, check the wire harness between the sensor and control board.
- Replace the oven temperature sensor if needed.
Detailed guide: Samsung Range C-10 and F-22 Error Codes.
F-22 Error Code
F-22 means the oven calibration data is corrupted. It often pops up after a power surge, firmware hiccup, or failed heating cycle.
How to fix it:
- Power cycle the range (unplug or flip breaker for 5 minutes).
- Try recalibrating: press and hold Bake + Broil for 3 seconds, then set the offset to 0°F.
- If F-22 returns, the main control board may need replacement.
bE Error Code
bE signals a bad touchpad — one or more touch keys are stuck or shorted. You’ll notice the oven beeps randomly or doesn’t respond to touches.
How to fix it:
- Clean the touchpad surface with a damp cloth — grease and residue can cause false touches.
- Power cycle the range.
- If bE is still there, replace the touchpad assembly or the display board (depending on your model).
General Tips for Samsung Ranges
Safety First
Always disconnect power before opening the range panels. Capacitors inside the control board can hold a charge even after unplugging. A multimeter with a non-contact voltage detector is worth having.
Check Your Model Number
Samsung uses the same error code for different failure modes depending on the model. Your model number is printed on a sticker inside the oven door (top or side edge) or on the back of the unit. Write it down before ordering any parts.
Ribbon Cables Are the Weak Point
Samsung ranges use wide flat ribbon cables between the display board, touchpad, and main control board. These can work loose over time from heat cycling or vibration. Before replacing any major part, open the back panel and reseat every ribbon cable you can see.
Know When to Call a Pro
Codes like 5E (short circuit) or codes that return after you’ve replaced the obvious parts are a signal to call a technician. Replacing a control board without proper diagnosis can get expensive fast.
Parts to Keep on Hand
- Digital multimeter
- Samsung oven temperature sensor
- Samsung range control board (check model compatibility)
- Samsung touchpad assembly (model-specific)
- Ribbon cable / flex cable for Samsung ranges