Posts
All the articles I've posted.
-
Samsung Refrigerator Defrost Thermostat Replacement Guide
Frost buildup, warm fridge, and icing evaporator coils mean your defrost thermostat failed. Replacing the bi-metal thermostat restores proper defrost cycling.
-
GE Refrigerator Water Inlet Valve Replacement - Signs & How-To
Inlet valve failures cause no ice, no dispenser water, slow fill, or leaks. Replacing a stuck or electrically failed valve restores flow.
-
Whirlpool Dryer Gas Valve Coil Replacement - Signs & How-To
Dryer heats once then stops, or igniter glows but burner won't light on later cycles. Replacing the gas valve solenoid coil kit fixes intermittent heating.
-
Maytag Dryer Door Switch Replacement - Signs & How-To
A faulty Maytag dryer door switch prevents the dryer from starting or stops it mid-cycle. Replacing the switch restores normal door-interlock operation.
-
GE Dryer Cycling & High-Limit Thermostat Replacement Guide
Dryer won't start, stops mid-cycle, runs too hot, or heat cuts on and off? A failed cycling or high-limit thermostat is often the fix.
-
Kenmore Washer Clutch/Splutch Assembly Replacement
Washer agitates but won't spin, spins slowly, or makes grinding noise during spin. Replacing the worn clutch/splutch assembly restores spin.
-
Maytag Washer Agitator Dogs Replacement - Signs & How-To
Upper agitator slips or spins freely instead of ratcheting during wash. Replacing worn agitator dogs and cam restores one-way drive action.
-
Kenmore Washer Motor Coupler Replacement - Signs & How-To
A worn or broken motor coupler causes your Kenmore direct-drive washer to fill and drain but not agitate or spin. Replacing it restores power transfer.
-
LG Washer Drive Belt Replacement - Signs & How-To
Drum not spinning, motor runs but basket doesn't turn, or squealing noise means your belt is worn or broken. Replacing it restores spin.
-
Rinnai Water Heater Leaking - Causes & Fix
Most likely an internal heat exchanger or piping leak triggering the leak detector. Inspect cabinet pan and all internal components for water.
-
Rinnai Water Heater Water Too Hot - Causes & Fix
Scale buildup in the heat exchanger blocks heat transfer and causes over-temperature faults. Flush the heat exchanger per Rinnai procedure.
-
Rinnai Water Heater Not Enough Hot Water - Causes & Fix
Usually too much simultaneous demand for the unit's capacity, low gas supply, or a dirty inlet filter restricting flow and heating output.
-
Rinnai Water Heater No Hot Water - Causes & Fix
Most often a clogged inlet water filter or insufficient flow to trigger firing. Clean the filter and verify minimum flow demand first.
-
Navien Water Heater No Ignition - Causes & Fix
Low gas pressure or a closed shutoff valve is the most common cause. Open the valve fully and verify gas supply before checking venting.
-
Navien Water Heater Leaking - Causes & Fix
Usually a loose fitting, leaking pressure relief valve, or clogged inlet filter causing flow issues. Isolate the leak source and check connections first.
-
Navien Water Heater Water Too Hot - Causes & Fix
Restricted water flow through the heater is the most common cause. Clean the inlet filter and check all valves are fully open.
-
Navien Water Heater Not Enough Hot Water - Causes & Fix
Flow sensor debris or sticking is the most likely cause when a Navien shows no error codes but won't produce hot water. Check and clean the sensor first.
-
Rheem Water Heater No Ignition - Causes & Fix
Low gas supply or a latched control fault. For LPG, check propane bottle level, cycle power at the outlet, and reopen the tap.
-
Navien Water Heater No Hot Water - Causes & Fix
Flow sensor not spinning properly due to debris is the most common cause. Open and close the pressure relief valve to clear it.
-
Rheem Water Heater Leaking - Causes & Fix
Usually a faulty T&P relief valve or loose pipe connection. Inspect the valve, connections, and tank seams to find the source.
-
Rheem Water Heater Water Too Hot - Causes & Fix
Usually a failed outlet temperature sensor or mineral scale buildup in a tankless unit (error code 16). Inspect the sensor and flush the heat exchanger.
-
Rheem Water Heater No Hot Water - Causes & Fix
Most often caused by ignition failure, flame loss, or insufficient water flow. Check the fault code on your unit's display first.
-
Rheem Water Heater Not Enough Hot Water - Causes & Fix
Usually caused by excessive demand or low flow rates. Check for simultaneous usage, verify minimum flow on tankless units, and flush sediment.
-
Fujitsu Mini Split Ice on Coils - Causes & Fix
Ice on indoor coils is usually caused by a dirty air filter or clogged evaporator blocking airflow. Clean or replace the filter first.